Video Selfview Default Fullscreenmode; Video Selfview Default Mode; Video Selfview Default Onmonitorrole; Video Selfview Default Pipposition - Cisco DX70 Administrator's Manual

Hide thumbs Also See for DX70:
Table of Contents

Advertisement

Cisco DX70 and DX80
Introduction

Video Selfview Default Mode

Define if the main video source (self-view) shall be displayed on screen after a call. The
position and size of the self-view window is determined by the Video Selfview Default
PIPPosition and the Video Selfview Default FullscreenMode settings respectively.
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Off/Current/On
Off: self-view is switched off when leaving a call.
Current: self-view is left as is, i.e. if it was on during the call, it remains on after the call; if
it was off during the call, it remains off after the call.
On: self-view is switched on when leaving a call.

Video Selfview Default FullscreenMode

Define if the main video source (self-view) shall be shown in full screen or as a small
picture-in-picture (PiP) after a call. The setting only takes effect when self-view is switched
on (see the Video Selfview Default Mode setting).
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Off/Current/On
Off: self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e.
if it was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the
call, it remains fullscreen after the call.
On: The self-view picture will be shown in fullscreen.

Video Selfview Default OnMonitorRole

Define which monitor to display the main video source (self-view) on after a call. Note that
this video system has only one monitor, so this value is fixed and cannot be changed.
Requires user role: ADMIN, INTEGRATOR
Default value: First
Value space: First
First: The self-view picture will be shown on the integrated screen.
D15362.06 DX70 and DX80 Administrator Guide CE9.2, NOVEMBER 2017.
Configuration
Peripherals
Maintenance

Video Selfview Default PIPPosition

Define the position on screen of the small self-view picture-in-picture (PiP) after a call.
The setting only takes effect when self-view is switched on (see the Video Selfview
Default Mode setting) and fullscreen view is switched off (see the Video Selfview Default
FullscreenMode setting).
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/
LowerLeft/LowerRight
Current: The position of the self-view PiP will be kept unchanged when leaving a call.
UpperLeft: The self-view PiP will appear in the upper left corner of the screen.
UpperCenter: The self-view PiP will appear in the upper center position.
UpperRight: The self-view PiP will appear in the upper right corner of the screen.
CenterLeft: The self-view PiP will appear in the center left position.
CentreRight: The self-view PiP will appear in the center right position.
LowerLeft: The self-view PiP will appear in the lower left corner of the screen.
LowerRight: The self-view PiP will appear in the lower right corner of the screen.

Video Selfview OnCall Mode

This setting is used to switch on self-view for a short while when setting up a call. The
Video Selfview OnCall Duration setting determines for how long it remains on. This applies
when self-view in general is switched off.
Requires user role: ADMIN, INTEGRATOR
Default value: On
Value space: Off/On
Off: Self-view is not shown automatically during call setup.
On: Self-view is shown automatically during call setup.
www.cisco.com — Copyright © 2017 Cisco Systems, Inc. All rights reserved.
128
Administrator Guide
System settings
System settings
Appendices

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dx80

Table of Contents