Digital Media Switchers: Send_Commands - AMX DGX1600-ENC Hardware Reference Manual

Digital Media Switchers: SEND_COMMANDs

IMPORTANT: The SEND_COMMANDs listed in this section are for the switcher only. For additional information on NetLinx commands
used in conjunction with this product, see "WebConsole & Programming Guide – NX-Series Controllers" (available at www.amx.com).
Note the following port information:
Commands derive their port addressing from the target D:P:S (Device:Port:System).

To distinguish the functionality of signal input and output ports from the overlapped device port numbers, the signal input

and output numbers are part of the command's action.
Video (with/without AIE*) input and output ranges:





Audio Switching Board (ASB and ASB-DAN) input and output ranges**:





* Because the Audio Insert/Extract Board can be set to insert/extract audio into/out of video inputs or outputs, the audio signals
from these boards switch as embedded audio in conjunction with the corresponding video signals.
** Audio Switching Board (ASB and ASB-DAN) signal routing is accomplished via SEND_COMMANDs (see below), via the System
Configuration interface (see page 163), or as embedded audio only via the control panel (see page 216).
^ For each system, one port is available as an additional input for downmix. The downmix port number follows sequentially after
the last audio only port (e.g., an Enova DGX 800 Switcher's downmix port is port number 17).
NOTE: All text is based on a Unicode index.
Switcher SEND_COMMANDs
Command
AI<input>O<output>
Switches audio input port
<input> to audio output port
<output>.
NOTE: This command is only
available when ASB boards are
in the system and correctly
installed (HSSI cable
connected for Enova DGX
800,1600, and 3200).
?AUTO_SETUP
Requests the current state of the
Auto-setup mode.
NOTE: Mode is also visible on
the System Configuration
interface's Switcher/Status
page.
AUTO_SETUP
Enables or Disables Auto-setup
mode.
NOTE: Mode can also be set via
the System Configuration
interface's Switcher/Status
page.
Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers
Enova DGX 800: 1-8
Enova DGX 1600: 1-16
Enova DGX 3200: 1-32
Enova DGX 6400: 1-64
Enova DGX 800: 1-8 embedded audio, 9-16 audio only^
Enova DGX 1600: 1-16 embedded audio, 17-24 audio only^
Enova DGX 3200: 1-32 embedded audio, 33-40 audio only^
Enova DGX 6400: 1-64 embedded audio, 65-80 audio only^
Description
IMPORTANT: This command must be sent to D:P:S port 1.
Syntax:
SEND_COMMAND <DEV>, "'AI<input>O<output>'"
Variables:
input = The source audio input port number to switch from.
output = The destination audio output port number to switch to.
NOTE: For information on Audio Switching Board input and output ports, see the information at
the top of this page.
Example:
SEND_COMMAND 5002:1:0, "'AI2O1,2'"
Switch audio input port #2 to audio outputs #1 and #2.
TIP: Any input can be switched to one, many, or all outputs.
Syntax:
SEND_COMMAND <DEV>, "'?AUTO_SETUP'"
Examples:
SEND_COMMAND 5002:1:0, "'?AUTO_SETUP'"
Returns a response of the form: ON|OFF
NOTE: Command affects system-wide Auto-setup ON|OFF settings.
Syntax:
SEND_COMMAND <DEV>, "'AUTO_SETUP-<ON|OFF>'"
Variables:
ON (default) = Enables Auto-setup so connected endpoints with default factory settings will
automatically be bound to the DGX Master and given specific Private IP addresses and device
numbers based on their channel number (see "Automatic Configuration of AMX Devices via ICS
LAN" on page 25)
OFF = Disables Auto-setup so connected endpoints will revert to traditional NDP/DHCP binding
Examples:
SEND_COMMAND 5002:1:0, "'AUTO_SETUP-OFF'"
Integrated Master – NetLinx® Programming
188