Advanced Setup Instructions And Additional Information; Dx80 Menu Structure - Banner Sure Cross Performance GatewayPro DX80P*A6 series Instruction Manual

®
Sure Cross Performance DX80 Wireless I/O Networks
5 Advanced Setup Instructions and Additional
Information
Refer to the following sections for advanced setup instructions or additional information on Banner's SureCross wireless
technology and its uses.

5.1 DX80 Menu Structure

The Gateways and Nodes each have their own menu structure and options.
5.1 DX80 Gateway Set-up Menu
When power is applied, the DX80 begins running. The display screen auto loops through the RUN menu and
communication begins between the Gateway and Node(s). Auto looping through the RUN menu is the normal operating
mode for all devices on the wireless network.
From the RUN Menu (or any menu), single-click button 1 to advance through the top-level menus. The device auto display
loops through the menu options if either of the RUN, DINFO, or FCTRY menus are selected. If the device is paused on the
SITE, DVCFG, or DERR menu options, the display does not auto loop.
To enter manual scrolling mode, double-click button 2 at the top level menu. Use the instructions shown in the chart below
to navigate the menu system. To return to the top level menus and auto display loop mode, double-click button 2 twice.
The * before the menu name indicates a top-level menu option. The () indicate submenu items.
When using Rotary Dial Addressing Mode, use the left rotary dial to set the Network ID (NID). Once changed, allow five
seconds for the devices to update to the new Network ID.
Single-click Button 1 to advance through menu
RUN
* * DINFO * FCTRY
Device Info Factory Info
AUTO AUTO
adjust the rotary
DISPLAY DISPLAY
switches to survey
LOOP LOOP
the selected Node
Single-click Single-click
Single-click Single-click Button 1
Button 1
Button 1 Button 1
(DEV)
NID XX NID XX
GATEWY GATEWY
(DEV) (DEV)
(NAME)
GATEWY GATEWY
XXXXXX
I/O XX I/O XX
XXXXXX
ON/OFF ON/OFF XXXXXX
(NID)
XX
(SLID)
XX
(BAUD)
XX
(PRTY)
XX
28
* SITE * DVCFG
Site Survey Device Config
Single-click Single-click
Button 2 Button 2
AUTO
DISPLAY
LOOP
adjust right rotary
switch to survey the
selected Node
(DEV)
NOD XX
Single-click
Button 2
(RADIO
AUTO
DISPLAY
MICRO)
LOOP
M XX
(NID)
V 00.0 A
R XX
Network ID
(LCD Single-click
Y XX
Button 2
MICRO) G XX
V 00.0 A
Double-click
Button 2
adjust rotary switches
(DX80
to set the network ID
S/N)
CUR XX
(0000)
NEW XX
(DX80
Single-click
Button 2
MODEL)
(0000-00)
SAVES NEW
VALUES
(PROD
DATE)
(00-00)
www.bannerengineering.com - Tel: 763.544.3164
* DERR
Device Error
New Error
* ERROR
Detected
Single-click
Button 2
Single-click
Button 2
Single-click Button 1 to advance through menu
NOD XX
EC XX CLEAR DISABL IGNORE
Single-click Single-click Single-click
Button 2 Button 2 Button 2
ERR ERR
ERASED DISABL
Next Single-click Single-click
Button 2 Button 2
Device
Single-click Button 1 to advance through menu
(SLID) (BAUD) (PRTY)
Slave ID Baud Rate Parity
Single-click Single-click Single-click
Button 2 Button 2 Button 2
None
9600
adjust rotary switches
19200 Even
to set slave ID, using
button 1 to select the
digits
38400 Odd
CUR XX
Single-click Single-click
Button 2
Button 2
NEW XX
Single-click
Button 2
SAVES SAVES
DISPLAYED
DISPLAYED
VALUE VALUE
SAVES NEW
VALUES
* Set to 000000 to use the serial number.
(XADR)
(MAXN)
Timing Extended Addressing
Single-click Single-click
Button 2 Button 2
Single-click
8 AUTO AUTO
Button 2
16
NETWRK
MANUAL
32
BINDNG
Single-click
Single-click
48
Button 2
Button 1 or 2
Single-click
Button 2
SET
Reboot
XADR
SAVES
DISPLAYED
ADJUST ROTARY
VALUE
SWITCH TO
SET XADR
*
XXXXXX
Single-click
Button 2
CONFRM
XADR
XXXXX
Single-click
Button 2
SAVED