Siemens SIMATIC ET 200SP Manual page 8
As-interface master cm as-i master st 3rk7137-6sa00-0bc1
Hide thumbs
Also See for SIMATIC ET 200SP:
- System manual (320 pages) ,
- Manual (270 pages) ,
- Operating instructions manual (166 pages)
Table of Contents
Advertisement
Table of contents
7.2.2
I/O addresses without configuration of the AS-i slaves in STEP 7 ........................................ 50
7.2.3
Special characteristics of AS-i Safety slaves ......................................................................... 55
7.3
transferred .............................................................................................................................. 56
7.3.1
Accessing AS-i analog data via the process image ............................................................... 58
7.3.2
Accessing AS-i analog data via acyclic services ................................................................... 58
8
Alarms, faults and system events ............................................................................................................ 61
8.1
Overview ................................................................................................................................ 61
8.2
Diagnostics in STEP 7 ........................................................................................................... 62
8.3
LED statuses .......................................................................................................................... 63
8.3.1
Arrangement of the LEDs on the CM AS-i Master ST ........................................................... 63
8.3.2
Meaning of the LEDs ............................................................................................................. 64
8.4
Diagnostic messages ............................................................................................................. 69
8.4.1
Alarms .................................................................................................................................... 69
8.4.2
Possible response to the diagnostic interrupt ........................................................................ 69
8.4.3
Error messages ...................................................................................................................... 70
8.5
Replacing a defective AS-i slave / automatic address programming .................................... 74
8.6
Duplicate address detection ................................................................................................... 76
8.7
Diagnosis via the web server ................................................................................................. 79
8.8
Fault indications/fault remedies ............................................................................................. 80
8.9
Data records for diagnostics .................................................................................................. 82
8.9.1
DS 92 Diagnostic data record (FW V1.1 and higher) ............................................................ 82
8.9.2
8.9.3
DS 97 Read and reset AS-i master error counters (FW V1.1 and higher) ............................ 89
8.9.4
DS 150 to DS 153 Read AS-i error counters ......................................................................... 89
8.9.4.1
DS 150 Read AS-i slave error counters 1/1A to 16/16A ........................................................ 92
8.9.4.2
DS 151 Read AS-i slave error counters 16/16A to 31/31A .................................................... 93
8.9.4.3
DS 152 Read AS-i slave error counters 1B to 16B ................................................................ 94
8.9.4.4
DS 153 Read AS-i slave error counters 16B to 31B .............................................................. 95
8.9.5
DS 154 Delete AS-i error counters (from FW V1.1) ............................................................... 96
9
Using the command interface .................................................................................................................. 97
9.1
Introduction ............................................................................................................................ 97
9.2
Command interface with SIMATIC S7 ................................................................................... 97
9.3
Command interface with controllers of other manufacturers ................................................. 98
9.4
Description of the AS-i commands ....................................................................................... 103
9.4.1
No. 00: Set_Permanent_Parameter ..................................................................................... 107
9.4.2
No. 01: GET_Permanent_Parameter ................................................................................... 108
9.4.3
No. 02: Write_Parameter ..................................................................................................... 109
9.4.4
No. 03: Read_Parameter ..................................................................................................... 110
9.4.5
No. 04: Store_Actual_Parameters ........................................................................................ 111
9.4.6
No. A5: Set_Permanent_Configuration ................................................................................ 112
9.4.7
No. A6: Get_Permanent_Configuration ............................................................................... 113
9.4.8
No. 07: Store_Actual_Configuration ..................................................................................... 114
9.4.9
No. A8: Read_Actual_Configuration .................................................................................... 115
8
AS-Interface master CM AS-i Master ST (3RK7137-6SA00-0BC1)
Manual, 07/2017, A5E02655262020A/RS-AD/004
Advertisement
Table of Contents
