Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
Page 3
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, customers are billed according to the cost of replacement materi- als, service time and freight.
Caution! A new battery is at risk of exploding if incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufac- turer. Discard used batteries according to the manufacturer's instruc- tions. MIO-2270 User Manual...
According to IEC 704-1:1982, the sound pressure level at the operator's position should not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of the statements contained herein. MIO-2270 User Manual...
Page 7
PC is on. Disconnect the power supply before implementing any configuration changes. A sudden rush of power after a jumper is connected or a card installed may dam- age sensitive electronic components. MIO-2270 User Manual...
Chapter General Introduction This chapter gives background information on the MIO-2270. Sections include: Introduction Product Features Specifications...
SoC dual-core GX-210JA 1.0 GHz and quad-core GX-415GA 1.5 GHz proces- sors. MIO-2270 supports up to 8 GB of DDR3 or DDR3L memory, features two USB 2.0 and two USB 3.0-compatible ports, one GbE (up to 1000 Mbps) interface, LVDS and VGA or HDMI support, high definition (HD) audio, and one half-size mini-PCIe and MIOe expansion slot.
Lanes 3 & 4: MIOe connector 1 x mSATA by Mini-PCIe socket (integrates USB signals, and supports either mSATA or USB interface modules) SATA Interface 1 x SATAIII (600 MB/s maximum data transfer rate) MIO-2270 User Manual...
L100 mm x W72 mm (3.9" x 2.8") 1.2.3.2 Height of Component Side (mm) 15.7 mm (heat sink) 1.2.3.3 Height of Solder Side (mm) 16.4 mm (rear I/O USB) 1.2.3.4 Weight (g) 420 g (0.93 lb, total package weight) MIO-2270 User Manual...
Chapter H/W Installation This chapter explains the setup procedures for the MIO-2270 hard- ware, including instructions for connecting jumpers, peripherals, switches, and indicators, as well as mechanical drawings. Please read all safety precautions before beginning installation.
Table 2.2: J1: LCD Power / Auto Power On Part No. 1653003260 Footprint HD_3x2P_79 Description Pin header 3*2P 180D(M) 2.0 mm SMD square pin Setting Function (1-2) +5 V (3-4) (default) +3.3 V (5-6) (default) Auto power on MIO-2270 User Manual...
Page 19
DDR3L (2-3)* DDR3 *default LAN Enable / Disable Part No. 1600000071 Footprint SW_3P_CJS-1201TA1 Description DIP SW CJS-1201TA1 SMD 3P SPDT P = 6.0 mm W = 2.5 mm Setting Function (1-2)* LAN Enable (2-3) LAN Disable *default MIO-2270 User Manual...
2.2.2.3 Display Interface Connections (CN3, CN15 and CN20) The MIO-2270 display interface supports either VGA or HDMI on rear I/O and is capable of driving a wide range of flat panel displays, including passive and active LCD displays.The board features three display connector types; among which, one rear I/O can accommodate either standard CRT VGA monitors or an HDMI display and one supports LVDS-type LCD panels.
Page 21
2.2.2.8 COM Port Connectors (CN12) MIO-2270 features one RS-232 and one RS-232 / 422 / 485 serial ports in a 10 x 2- pin header. This provides connections for serial devices or a communication network. The pin assignments for the COM port connector are presented as Appendix A.
Page 22
SMBus proto- cols, facilitating multiple simultaneous device control. 2.2.2.17 Battery Connector (BH1) MIO-2270 supports a 3 V / 210 mAH CR2032 lithium battery with a wire via a battery connector (BH1). Note! To clear CMOS, please follow the steps below: 1.
40.96 65.41 83.31 97.15 Unit: mm Figure 2.8 Board dimensions and layout (coastline with power connector and optional heat spreader) 104.36 16.51 40.96 65.41 83.31 97.15 Unit: mm Figure 2.9 Board dimensions and layout (coastline with cooler) MIO-2270 User Manual...
MIOe connector is 16 mm (a height of 19 mm is also avail- able upon request). The height of the MIO-2270 power connector (including the cable) should be considered when assembling the system or stacking the MI/O module.
Presently, the height of our heat spreader is 11.2 mm (Advantech P/N: 1960065075N001). However, should you require a heat spreader of another height to better fit chassis, Advantech can customize this for you. Please con- tact our sales center for further details.
AMI's BIOS ROM has a built-in setup program that allows users to modify the basic system configuration. This information is stored in flash ROM, which ensures that the setup information is retained when the power is turned off. MIO-2270 User Manual...
BIOS can support your CPU. If no number is assigned to the patch code, please contact an Advantech application engineer to obtain an up-to-date patch code file. This guarantees that your CPU system status is valid. After ensuring that a number is assigned to the patch code, press <DEL>...
3.2.2 Advanced BIOS Features Setup Select the Advanced tab of the MIO-2270 setup screen to enter the Advanced BIOS setup screen. Users can select any item, such as CPU Configuration, in the left frame of the screen to access the sub menu for that item. Users can view the Advanced BIOS setup options by highlighting items using the <Arrow>...
Page 33
This item allows users to enable or disable PCI device PERR# generation. SERR# Generation This item allows users to enable or disable PCI device SERR# generation. PCI Express Settings This item allows users to change the PCI Express device settings. MIO-2270 User Manual...
Page 34
This item allows users to enable or disable BIOS ACPI auto configuration. Enable Hibernation This item allows users to enable or disable the hibernation function (if supported by the OS). ACPI Sleep State This item allows users to select the ACPI states used for system suspension. MIO-2270 User Manual...
Page 35
3.2.2.3 Trusted Computing TPM Support This item allows users to enable or disable TPM support for security. MIO-2270 User Manual...
Page 36
This item allows users to enable or disable system wake on alarm event. Wake System with Dynamic Time This item allows users to enable or disable system wake on alarm event, and specify a delay interval of 1 to 5 minutes. MIO-2270 User Manual...
Page 37
This item allows users to auto enable or disable C6 function. CPB Mode This item allows users to auto enable or disable CPB. Node 0 Information This item allows users to view details of the memory information related to node MIO-2270 User Manual...
Page 38
3.2.2.6 IDE Configuration IDE Configuration This item allows users to view SATA Port 0 / Port 1 information. MIO-2270 User Manual...
Page 39
This item allows users to specify the USB mass storage device start unit com- mand time-out. Device Power-up Delay This item allows users to specify the maximum time before the device reports itself to the host controller. MIO-2270 User Manual...
Page 40
3.2.2.8 SMART Settings SMART Self Test This item allows users to enable or disable the SMART self-test function. MIO-2270 User Manual...
Page 41
This item allows you users to select serial Port 1 / Port 2 and view their detailed functions. Watch Dog Function Configuration This item allows users to enable or disable WDT time. Backlight Configuration This item allows users to select the backlight mode. MIO-2270 User Manual...
Page 42
3.2.2.10 H/W Monitor PC Health Status This page displays all information related to the system temperature / voltage. MIO-2270 User Manual...
This item allows users to view options for the South Bridge items. North Bridge This item allows users to view options for the North Bridge items. LVDS Config This item allows users to view options for the display items. MIO-2270 User Manual...
Page 44
This item allows users to specify the primary video device for first output. Integrated Graphics This item allows users to enable or disable the integrated graphics controller. PSPP Policy This item allows users to specify the PCIe speed power policy. MIO-2270 User Manual...
Page 45
PCI-E Port This item allows users to view the options for PCI-E device control. Restore on AC Power Loss This item allows users to select the system restore states in the event of an AC power loss. MIO-2270 User Manual...
Page 46
3.2.3.3 North Bridge Configuration Memory Configuration This item allows users to select the memory frequency. 2nd LVDS Backlight Control This item allows users to select the LVDS backlight mode. MIO-2270 User Manual...
Page 47
3.2.3.4 LVDS Configuration LVDS This item allows users to enable or disable LVDS panel function. LVDS Panel Config Select This item allows users to select the LVDS panel resolution type. MIO-2270 User Manual...
CSM16 Parameters This item allows you users to change the “GateA20 Active”, “Option ROM Mes- sages”, and “INT19 Trap Response” functions. CSM Parameters This item allows users to enable or disable CSM support and OpROM policy. MIO-2270 User Manual...
3.2.5 Security Configuration Select the Security tab from the MIO-2270 main BIOS setup menu. All security setup options, such as password and virus protection can be accessed from this menu. To access the sub menu for the options of each item, select the item and press <Enter>.
This item allows users to save all changes as the user defaults. Restore User Defaults This item allows users to restore the user defaults for all options. Boot Override This item allows users to override the boot device priority specifications. MIO-2270 User Manual...
S/W Introduction The aim of Advantech Embedded Software Services is to “enhance the quality of life using Advantech platforms and Microsoft® Windows® embedded technology.” Win- dows embedded software products are supported on Advantech platforms to more effectively support the embedded computing community. Consequently, customers are freed from the hassle of dealing with multiple vendors (hardware suppliers, sys- tem integrators, and/or embedded OS distributors) for projects.
However, because of the inaccuracy of many commercially available hardware moni- toring chips, Advantech has developed a unique scheme for hardware monitoring; that is, using a dedicated micro-processor and specifically designed algorithms to provide accurate, real-time and reliable data, thereby offering more reliable system protection.
If a previous version is installed, please see the [Maintenance Setup] section. If not located, an alternative window appears. Click <Next>. MIO-2270 User Manual...
Some function tabs might not appear for the test application if your platform does not support such functions. For a complete support list, please refer to Appendix A. The steps for testing all functions of this application are described below. MIO-2270 User Manual...
Page 56
Test Write Multiple Output Pins – Click the <Multiple Pins> radio button. – Enter the pin numbers from ‘0x01’ to ‘0x0F’ to choose the pin numbers to write the value of the output pin. The pin numbers are ordered bit-wise, that MIO-2270 User Manual...
Page 57
Click the <write SMBus data> button to write data to the device through SMBus. Read a word – Click the <Access a word> radio button. – Enter the slave device address in the Slave address field. MIO-2270 User Manual...
Page 58
Input all desired data in the Result field in hexadecimal format and divided by commas, for example, 0x50, 0x60, 0x7A. – Click the <write SMBus data> button to write the data to the device via the SMBus. MIO-2270 User Manual...
Page 59
Move the slider in increments, using either the mouse or the direction keys, or click the UP button to increase the brightness. – Move the slider in decrements, using either the mouse or the direction keys, or click the DOWN button to decrease the brightness. MIO-2270 User Manual...
Page 60
Before the timer counts down to zero, the timer can be reset by clicking the <Refresh> button. Subsequently, the Timeout Countdown field displays the value of the Set Timeout field. To stop the watchdog timer, just click the <Stop> button. MIO-2270 User Manual...
Page 61
If certain data values are not supported by the platform, the corresponding data field is grayed-out and the value listed is 0. For more details regarding MIO-2270 software APIs, please contact your dealer or Advantech AE. MIO-2270 User Manual...
Battery Table A.3: J1: LCD Power/Auto Power On Part No. 1653003260 Footprint HD_3x2P_79 Description Pin header 3*2P 180D(M) 2.0 mm SMD square pin Setting Function (1-2) +5 V (3-4) (default) +3.3 V (5-6) (default) Auto power on MIO-2270 User Manual...
Page 65
DIP SW CJS-1201TA1 SMD 3P SPDT P = 6.0 mm W = 2.5 mm Setting Function (1-2) * LAN enable (2-3) LAN disable *default 12 V Power Input Part No. 1655003962 Footprint WF_2P_156_D_A3963WV2 Description Pin name +12 V DDR3 SODIMM Part No. 1651002083 Footprint DDR3_204P_AS0A626-JA Description Pin name MIO-2270 User Manual...
Page 66
Footprint WF14P_49_BOX_RA_85204-14001 Description Pin name LVDS0_CLK- LVDS0_CLK+ LVDS0_D2- LVDS0_D2+ LVDS0_D1- LVDS0_D1+ LVDS0_D0- LVDS0_D0+ +5 V or +3.3 V +5 V or +3.3 V HD Audio Part No. 1653003719 Footprint HD_5x2P_79_RA_21N22050 Description Pin name LOUTR LINR LOUTL LINL MIO-2270 User Manual...
Page 67
Wafer 1.25 mm 5P 90D Male SMD 852040 Pin name +12V ENABKL GPIO Part No. 1653005261 Footprint HD_5x2P_79 Description Pin header SMD 5*2P 180D(M) 2.0 mm Pin name +5 V GPIO4 GPIO0 GPIO5 GPIO1 GPIO6 GPIO2 GPIO7 GPIO3 MIO-2270 User Manual...
Page 68
DC jack (upon request) Part No. 1652005684 Footprint PJ_3P_DCJ-RPBT5NW-25 Description Pin name +VIN CN10 mSATA Part No. 1654002538 Footprint MINIPCIE_HALF_PICO_ITX Description Pin name +3.3V +1.5V +3.3V MIO-2270 User Manual...
Page 69
CN10 mSATA Part No. 1654002538 Footprint MINIPCIE_HALF_PICO_ITX Description Pin Name +1.5V SMB_CLK SMB_DAT USB P- USB P+ +3.3V +3.3V +1.5V +3.3V MIO-2270 User Manual...
Page 78
CN16 MIOe Part No. 1654006235 Footprint BB_40x2P_32_1625x285_2HOLD Description Pin name +12VSB +12VSB +5VSB +5VSB +5VSB +5VSB MIO-2270 User Manual...
Page 79
BI_DB+(GHz) BI_DC+(GHz) BI_DC-(GHz) BI_DB-(GHz) BI_DD+(GHz) BI_DD-(GHz) CN18 CPU FAN Part No. 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 2.0 mm 180D(M) DIP A2001WV2-2P Pin name +12 V CN20 HDMI_19H Part No. 1654011175-01 Footprint HDMI_19P_QJ51191-LFB4-7F Description Pin name MIO-2270 User Manual...
Page 80
CN21 SATA Part No. 1654007578 Footprint SATA_7P_WATF-07DBN6SB1U Description Pin name CN22 SMBus Part No. 1655904020 Footprint FPC4V-125M Description Wafer SMT 1.25 mm S/T type 4P 180D(M) 85205-04001 Pin name SMB_DAT SMB_CLK +5 V MIO-2270 User Manual...
Page 81
1653005260 Footprint HD_5x2P_79_N10 Description Pin header 2*5P 180D(M) 2.0 mm SMD idiot-proof Pin name +5 V +5 V A_D- B_D- A_D+ B_D+ CN25 External USB2.0+USB3.0 Part No. 1654009860 Footprint USB_9x2P_2360009-603-R Description Pin name SSRX- SSRX+ SSTX- SSTX+ MIO-2270 User Manual...
Page 82
CN31 Mini PCIe Part No. 1654002538 Footprint MINIPCIE_HALF_PICO2600 Description Pin name WAKE# +3.3VSB +1.5V REFCLK- REFCLK+ PERST# PERn0 +3.3VSB PERp0 MIO-2270 User Manual...
Page 83
CN31 Mini PCIE Part No. 1654002538 Footprint MINIPCIE_HALF_PICO2600 Description Pin name +1.5 V SMB_CLK PETn0 SMB_DAT PETp0 USB D- USB D+ +3.3 VSB +3.3 VSB +1.5 V +3.3 VSB MIO-2270 User Manual...
IRQ0 Interval timer IRQ1 Keyboard IRQ2 Interrupt from controller 2 (cascade) IRQ3 COM2 IRQ4 COM1 IRQ5 Available IRQ6 Available IRQ7 Available IRQ8 IRQ9 Reserved IRQ10 Available IRQ11 Available IRQ12 Reserved IRQ13 Math coprocessor IRQ14 Reserved IRQ15 Reserved MIO-2270 User Manual...