Emerson Unidrive M400 Series User Manual page 105

Safety Product Mechanical
information information installation
Parameter
07.001 Analog Input 1 (T2/3)
07.002 Analog Input 2 (T5)
07.004 Stack Temperature
07.005 Auxiliary Temperature
07.007 Analog Input 1 Mode (T2/3)
07.008 Analog Input 1 Scaling (T2/3)
07.009 Analog Input 1 Invert (T2/3)
07.010 Analog Input 1 Destination A (T2/3)
07.011 Analog Input 2 Mode (T5)
07.012 Analog Input 2 Scaling (T5)
07.013 Analog Input 2 Invert (T5)
07.014 Analog Input 2 Destination A (T5)
07.019 Analog Output 1 Source A (T7)
07.020 Analog Output 1 Scaling (T7)
07.021 Analog Output 1 Mode (T7)
07.022 Analog Output 2 Source A (T8)
07.023 Analog Output 2 Scaling (T8)
07.024 Analog Output 2 Mode (T8)
07.026 Analog Input 1 Preset on Current Loss (T2/3)
07.027 Analog Input 2 Preset on Current Loss (T5)
07.028 Analog Input 1 Current Loop Loss (T2/3)
07.029 Analog Input 2 Current Loop Loss (T5)
07.030 Analog Input 1 Offset (T2/3)
07.031 Analog Input 2 Offset (T5)
07.034 Inverter Temperature
07.035 Percentage Of d.c. Link Thermal Trip Level
07.036 Percentage Of Drive Thermal Trip Level
07.037 Temperature Nearest To Trip Level
07.046 Thermistor Type
07.047 Thermistor Feedback
07.048 Thermistor Trip Threshold
07.049 Thermistor Reset Threshold
07.050 Thermistor Temperature
07.051 Analog Input 1 Control (T2/3)
07.052 Analog Input 2 Control (T5)
07.055 Analog Output 1 Control (T7)
07.056 Analog Output 2 Control (T8)
07.061 Analog Input 1 Minimum Reference (T2/3)
07.062 Analog Input 1 At Minimum Reference (T2/3)
07.063 Analog Input 1 Maximum Reference (T2/3)
07.064 Analog Input 1 At Maximum Reference (T2/3)
07.065 Analog Input 2 Minimum Reference (T5)
07.066 Analog Input 2 At Minimum Reference (T5)
07.067 Analog Input 2 Maximum Reference (T5)
07.068 Analog Input 2 At Maximum Reference (T5)
07.090 Analog Input 1 Destination B (T2/3)
07.094 Analog Input 2 Destination B (T5)
07.099 Analog Output 1 Source B (T7)
07.102 Analog Output 2 Source B (T8)
RW Read / Write RO Read only
ND No default value NC Not copied
Unidrive M400 Control User Guide
Issue Number: 1
Electrical Getting Basic
installation started parameters the motor
Range ( )
OL
±100.00 %
0.00 to 100.00 %
±250 °C
±250 °C
4-20mA Stop (-6), 20-4mA Stop (-5),
4-20mA Low (-4), 20-4mA Low (-3),
4-20mA Hold (-2), 20-4mA Hold (-1), 0-20mA (0),
20-0mA (1), 4-20mA Trp (2), 20-4mA Trp (3),
4-20mA (4), 20-4mA (5), Voltage (6)
0.000 to 10.000
Off (0) or On (1)
0.000 to 30.999
4-20mA Stop (-6), 20-4mA Stop (-5),
4-20mA Low (-4), 20-4mA Low (-3),
4-20mA Hold (-2), 20-4mA Hold (-1), 0-20mA (0),
20-0mA (1), 4-20mA Trp (2), 20-4mA Trp (3),
4-20mA (4), 20-4mA (5), Voltage (6), Digital (7)
0.000 to 10.000
Off (0) or On (1)
0.000 to 30.999
0.000 to 30.999
0.000 to 40.000
Voltage (0), 0-20mA (1), 4-20mA (2), Digital (3)
0.000 to 30.999
0.000 to 40.000
Voltage (0), 0-20mA (1), 4-20mA (2), Digital (3)
4.00 to 20.00
4.00 to 20.00
Off (0) or On (1)
Off (0) or On (1)
±100.00 %
±100.00 %
±250 °C
0 to 100 %
0 to 100 %
0 to 29999
DIN44081 (0), KTY84 (1), PT1000 (2), PT2000 (3),
Other (4)
0 to 4000 Ω
0 to 4000 Ω
0 to 4000 Ω
-50 to 300 °C
0 to 5
0 to 5
0 to 15
0 to 15
±100.00 %
±100.00 %
±100.00 %
±100.00 %
0.00 to 100.00 %
±100.00 %
0.00 to 100.00 %
±100.00 %
0.000 to 30.999
0.000 to 30.999
0.000 to 30.999
0.000 to 30.999
Num Number parameter Bit
PT Protected parameter RA
Running NV Media Card
Optimization
Operation
RFC-A OL
Bit parameter Txt Text string
Rating dependent US User save
Onboard Advanced
Diagnostics
PLC parameters
Default ( )
RFC-A
RO Num
RO Num
RO Num
RO Num
Voltage (6) RW Txt
1.000 RW Num
Off (0) RW Bit
1.036 RW Num
Voltage (6) RW Txt
1.000 RW Num
Off (0) RW Bit
1.037 RW Num
2.001 RW Num
1.000 RW Num
Voltage (0) RW Txt
4.002 RW Num
1.000 RW Num
Voltage (0) RW Txt
4.00 RW Num
4.00 RW Num
RO Bit
RO Bit
0.00 % RW Num
0.00 % RW Num
RO Num
RO Num
RO Num
RO Num
DIN44081 (0) RW Txt
RO Num
3300 Ω RW Num
1800 Ω RW Num
RO Num
0 RW Num
0 RW Num
0 RW Num
0 RW Num
-100.00 % RW Num
-100.00 % RW Num
100.00 % RW Num
100.00 % RW Num
0.00 % RW Num
0.00 % RW Num
100.00 % RW Num
100.00 % RW Num
RO Num
RO Num
RO Num
RO Num
Bin Binary parameter
PS Power-down save
UL
information
Type
ND NC PT FI
ND NC PT FI
ND NC PT
ND NC PT
US
US
US
DE PT US
US
US
US
DE PT US
PT US
US
US
PT US
US
US
US
US
ND NC PT
ND NC PT
US
US
ND NC PT
ND NC PT
ND NC PT
ND NC PT
US
ND NC PT FI
US
US
ND NC PT FI
US
US
US
US
US
US
US
US
US
US
US
US
DE PT US
DE PT US
PT US
PT US
FI Filtered
DE Destination
105