Node Default Settings; Table C-5 Node Default Settings - Cisco ONS 15600 Reference Manual

Appendix C Network Element Defaults
Table C-4 ASAP Card Default Settings (continued)
Default Name
ASAP_4.STM64-PORT.pmthresholds.path.nearend.1day.PPJC-PGEN
ASAP_4.STM64-PORT.pmthresholds.path.nearend.1day.SES
ASAP_4.STM64-PORT.pmthresholds.path.nearend.1day.UAS
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.15min.BBE
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.15min.EB
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.15min.ES
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.15min.OFS
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.15min.SES
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.1day.BBE
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.1day.EB
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.1day.ES
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.1day.OFS
ASAP_4.STM64-PORT.pmthresholds.rs.nearend.1day.SES
C.3 Node Default Settings
Table C-5 on page C-29
provides the following user-configurable defaults for each Cisco ONS 15600 SDH node:
•
•
•
•
•
78-18400-01
lists the node-level default settings for the Cisco ONS 15600 SDH. Cisco
Circuit settings—Set the administrative state and subnetwork connection protection (SNCP) circuit
defaults.
General settings—Set general node management defaults, including whether to use Daylight
Savings Time (DST), the IP address of the Network Time Protocol/Simple Network Time Protocol
(NTP/SNTP) server to be used, the time zone where the node is located, the signal degrade (SD)
path bit error rate (BER) value, the defaults description, whether automatic autonomous Transcation
Language One (TL1) reporting of PM data is enabled for cross-connect paths on the node, whether
or not to allow ports to be disabled when they are providing services (when the default is set to
FALSE users must remove or disable the services first, then put the ports out of service), and
whether to report loopback conditions on ports in the Locked,maintenance state.
Network settings—Set default gateway node type, and whether to raise an alarm when the backplane
LAN cable is disconnected.
OSI settings—Set the Open System Interconnection (OSI) main setup, generic routing
encapsulation (GRE) tunnel default, the link access protocol on the D channel (LAP-D), the router
subnet, and the TID address resolution protocol (TARP) settings.
1+1 protection settings—Set whether or not protected circuits have bidirectional switching, are
revertive, and what the reversion time is.
Default Value Default Domain
5760 (count) 0 - 691200000
7 (seconds) 0 - 86400
10 (seconds) 0 - 86400
10000 (count) 0 - 2212200
10000 (B1 0 - 2151900
count)
500 (seconds) 0 - 900
500 (seconds) 0 - 900
500 (seconds) 0 - 900
100000 0 - 212371200
(count)
100000 (B1 0 - 206582400
count)
5000 0 - 86400
(seconds)
5000 0 - 86400
(seconds)
5000 0 - 86400
(seconds)
Cisco ONS 15600 SDH Reference Manual, Release 9.0
C.3 Node Default Settings
C-27