Asap Connectors; Asap Covers And Plugs - Cisco ONS 15600 Reference Manual

2.8.1 ASAP Connectors

The ASAP card provides up to 16 Telcordia GR-253-CORE compliant, SDH STM-1, STM-4, STM-16,
or Gigabit Ethernet ports, or up to 4 Telcordia GR-253-CORE compliant, SDH STM-64 ports, in any
combination of line rates. The ASAP card, when used with the 4-Port I/O (4PIO) module, has up to 16
physical connector adapters (known as Small Form-factor Pluggables [SFPs]). The SFP ports operate at
up to 2488.320 Mbps over a single-mode fiber. The ASAP card, when used with the 1-Port I/O (1PIO)
module, has up to 4 physical connector adapters (known as 10Gigabit Small Form Factor Pluggables
[XFPs]). The XFP ports operate at up to 9953.280 Mbps over a single-mode fiber. Both XFP and SFP
physical connector adapters have two fibers per connector adapter (transmit [Tx] and receive [Rx]). The
ASAP card supports VC3 payloads and concatenated payloads at VC4, VC4-2c, VC4-3c, VC4-4c,
VC4-8c, VC4-16c and VC4-64c signal levels. The ASAP card is interoperable with ONS 15454 SDH
E-Series, G-Series, and ML-Series Ethernet cards.
There are three major components to the ASAP card:
•
•
•
2.8.1 ASAP Connectors
An ASAP carrier card supports any combination of four 4PIOs or 1PIOs. Each 4PIO supports up to four
SFPs, while each 1PIO supports one SFP/XFP. The maximum configuration for an ASAP card is 16 SFP
or 4 XFP ports, or a mix of both. The ports can each be provisioned as either STM-1, STM-4, STM-16,
STM64 (1PIO only), or Gigabit Ethernet.
In addition, the ports can be provisioned with STM-16 dense wavelength division multiplexing (DWDM)
SFPs. 32 SFPs, each with separate product IDs (PIDs), allow operation on 32 channels, separated by
100 GHz on the ITU grid. The modules offer operation in the red band from 1546.12 to 1560.61 nm and
in the blue band from 1530.33 to 1544.53 nm. These SFPs can be used in Metro, Regional, or Long Haul
applications. Eight ASAP cards can be installed in a shelf, and up to four ITU-T SFPs can be plugged
into each of the four 4PIO/PIMs (or one XFP in the 1PIO), providing a maximum of 128 ITU-T SFPs in
a single shelf.
For detailed information about SFPs/XFPs, see the
determine the line rates supported by each SFP/XFP, see the
page

2.8.2 ASAP Covers and Plugs

The covers and plugs that are shipped with the ASAP carrier card, 4PIOs, 1PIOs, and SFPs/XFPs must
be used in configurations where any of the these slots are unoccupied.
Cisco ONS 15600 SDH Reference Manual, Release 9.0
2-20
Carrier card, which can be installed in Slots 1 through 4 and 11 through 14
4PIO and 1PIO modules, also called Pluggable Input/Output Module (PIMs), which plug into the
ASAP carrier card
SFPs/XFPs, called Pluggable Port Modules (PPMs) in CTC, which plug into the 4PIO or 1PIO
(PIM) module and provide the fiber interface using a female LC connector
A-12.
"2.10 SFP/XFP Modules" section on page
"A.3 SFP/XFP Specifications" section on
Chapter 2 Card Reference
2-26. To
78-18400-01