Advertisement
Quick Start Guide
H
a
r
d
w
a
r
e
O
v
e
H
a
r
d
w
a
r
e
O
v
e
The Front LEDs
Lit red when power is on.
Lit green when the
system is ready.
Lit when connected to an Ethernet
device. Lit green when the speed of
transmission hits 10/100Mbps;
Blink when data is being
Transmitted / Received.
The Rear Ports
Power
Antenna
ON/OFF
switch
Connect with the
supplied power
adapter.
* Note 1. For advanced reset and restore setting, please refer to user manual.
2. For WPS configuration, please refer to the WPS section of User Manual.
2
r
v
i
e
w
r
v
i
e
w
When the device power
is on, press to reset or to
restore its factory
default setting.
(
(
B
B
i
i
P
P
A
A
C
C
7
7
3
3
0
0
0
0
W
W
O
O
(
1
)
W
P
S
:
P
r
e
s
s
2
(
1
)
W
P
S
:
P
r
e
s
s
2
flashes green to trigger WPS function.
(
2
)
W
i
r
e
l
e
s
s
O
N
/
(
2
)
W
i
r
e
l
e
s
s
O
N
/
s
s
e
e
c
c
o
o
n
n
d
d
s after WPS LED is off to switch on
s
wireless function. Press over 6 seconds again
for disable wireless function.
Lit green when a wireless
connection is established.
Blink when data is being
sent / received.
(
B
i
P
A
C
7
3
0
0
W
O
n
(
B
i
P
A
C
7
3
0
0
W
O
n
WPS: Flash green when
WPS configuration is in
progress.
*1
n
n
l
l
y
y
)
)
-
6
s
e
c
o
n
d
s until
W
P
S
L
E
D
-
6
s
e
c
o
n
d
s
W
P
S
L
E
D
*2
O
F
F
S
w
i
t
c
h
:
P
r
e
s
s
o
v
e
r
6
O
F
F
S
w
i
t
c
h
:
P
r
e
s
s
o
v
e
r
6
Lit green when the device
is successfully connected
to an ADSL DSLAM. ("Line
sync").
l
y
)
Lit red when WAN port
l
y
)
fails to get IP address.
Lit green when WAN
port gets IP address
successfully.
Connect your
Connect the supplied
computer to a
RJ-11 cable to this
LAN port with
port when
the included
connecting to the
Ethernet cable.
ADSL/telephone
network.
(
(
B
B
i
i
P
P
A
A
C
C
E
W
A
N
:
E
W
A
N
:
p
o
r
t
#
1 as a WAN port for
p
o
r
t
#
1
connecting to Cable Modem,
VDSL, fiber modem or PON
optic lines with RJ-45 cable.
7
7
3
3
0
0
0
0
W
W
O
O
n
n
l
l
y
y
)
)
I
t
o
f
f
e
r
s
i
t
s
E
t
h
e
r
n
e
t
I
t
o
f
f
e
r
s
i
t
s
E
t
h
e
r
n
e
t
Advertisement
