Related Manuals for Billion BiPAC 5200W
Summary of Contents for Billion BiPAC 5200W
-
Page 1: User Manual
BiPAC 5200W Wireless-N ADSL2+ Firewall Router User Manual Version Released: 2.12.24.0(SRE2.C3)3.12.8.200 Last Revised Date:12-31-2010... -
Page 2: Table Of Contents
1.3 Hardware Specifications.....................6 1.3.1 Physical Interface ....................6 1.4 Applications for the BiPAC 5200W ................7 Chapter 2 ..........................8 2.1 Important note for using the BiPAC 5200W ..............8 2.2 Package Contents ......................9 2.3 The Front LEDs ......................10 2.4 The Rear Ports ......................11 2.5 Cabling ........................12... - Page 3 3.5 Information from your ISP ..................24 3.6 Configuring with your Web Browser .................25 Chapter 4 ...........................26 4.1 Quick Start........................27 4.2 Interface Setup ......................31 4.2.1 Internet ......................31 4.2.2 LAN........................35 4.2.3 Wireless ......................37 4.3 Advanced Setup .......................43 4.3.1 Firewall ......................43 4.3.2 Routing ......................44 4.3.3 NAT........................46 4.3.4 QoS ........................52 4.3.5 ADSL .........................55...
-
Page 4: Chapter 1
Introduction the BiPAC 5200W 1.1 Introducing the BiPAC 5200W Router The BiPAC 5200W is an economical ADSL2+ router ideal for Home and SOHO users to enjoy improved Wireless Access Speed with a maximum operational speed of 150Mbps.It delivers the highest level of security with higher speed and better coverage of wireless-g solutions. -
Page 5: Upgrade Wireless Access
Internet. 1.1.4 Easy Network Management A user-friendly, web-based user interface makes installing and managing the BiPAC 5200W extremely easy. With support for both DHCP client and server, system administrators can manage IP assignment without having to reconfigure other stations and fitting the router into... -
Page 6: Features
1.2 Features • Base on Wireless-N Technology, and compliant with IEEE 802.11g, 802.11b standards • High-speed wireless connection up to 150Mbps • Wireless-N AP with Wi-Fi Protected Access (WPA-PSK/WPA2-PSK) and Wired Equivalent Privacy (WEP) support • High speed Internet access with ADSL2/2+; backward compatible with ADSL •... -
Page 7: Network Protocols And Features
• Compliant with ADSL2+ Standards - G.dmt.bis plus (ITU G.992.5) - ADSL2+ Annex M (ITU G.992.5 Annex M) (available for BiPAC 5200WA model only) 1.2.2 Network Protocols and Features • NAT, static routing and RIP-1/2 • Multi-to-multi NAT • Transparent Bridging •... -
Page 8: Wireless Lan
1.2.5 Wireless LAN • Compatible with IEEE 802.11g, 802.11b standards. • Up to 150Mbps wireless operation rate • 2.4 GHz–2.484 GHz frequency range • 64/128 bits WEP supported for encryption • Wireless Security with WPA-PSK/ WPA2-PSK support 1.2.6 ATM and PPP Protocols •... -
Page 9: Hardware Specifications
1.3 Hardware Specifications 1.3.1 Physical Interface • DSL: ADSL port • Ethernet: 4-port 10/100M auto-crossover (MDI/MDI-X) switch • Factory default reset button • Power jack • Power switch • WLAN: 1 antenna... -
Page 10: Applications For The Bipac 5200W
1.4 Applications for the BiPAC 5200W BiPAC 5200W... -
Page 11: Chapter 2
Chapter 2 Installing the BiPAC 5200W 2.1 Important note for using the BiPAC 5200W Do not use the router in high humidity or high temperatures. Do not use the same power source for the router as other equipment. Do not open or repair the case yourself. If the router is too hot,... -
Page 12: Package Contents
2.2 Package Contents BiPAC 5200W ADSL2+ Firewall Router Quick Start Guide CD containing user manual Ethernet (CAT-5 LAN) cable RJ-11 ADSL/telephone cable Power adapter Splitter/ Micro-filter (Optional) -
Page 13: The Front Leds
2.3 The Front LEDs BiPAC 5200W Meaning When the power is plugged in, it will lit Red and when the system is ready, it will lit Green. Whilst the system is rebooting Power or firmware upgrading, the LED light flashes. -
Page 14: The Rear Ports
2.4 The Rear Ports BiPAC 5200W Port Meaning Antenna Connect the antenna to this port. Power Power on/off switch. Switch Power Connect the supplied power adapter to this jack. After the device is powered on, press it to reset the device or restore to factory default settings. -
Page 15: Cabling
LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them... -
Page 16: Chapter 3
If not, please refer to your Windows-related or other operating system manuals. Any TCP/IP capable workstation can be used to communicate with or through the BiPAC 5200W. To configure other types of workstations, please consult the manufacturer’s documentation. -
Page 17: Configuring Pc In Windows 7
3.1.1 Configuring PC in windows 7 1. Go to Start. Click on Control Panel. Then click Network Internet. 2. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. Select Local Area... - Page 18 4. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 5. In the TCP/IPv4 properties window, select the Obtain an IP address automatically Obtain Server address automatically radio buttons. Then click OK to exit the setting. 6. Click OK again in the Local Area Connection Properties window to apply the new configuration.
-
Page 19: Configuring Pc In Windows Xp
3.1.2 Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. -
Page 20: Configuring Pc In Windows 2000
3.1.3 Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. -
Page 21: Configuring Pc In Windows 98/Me
3.1.4 Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3. -
Page 22: Configuring Pc In Windows Nt4.0
3.1.5 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK. -
Page 23: Step-By-Step Installation
3.2 Step-by-Step Installation 1. Insert the CD-ROM into CD-ROM drive 2. Execute Windows Utility 3. The Welcome screen will appear, click Next. 4. The Hardware Installation screen will appear. Four links are shown on the screen. Click them one by one and follow the guidelines to complete hardware installation. - Page 24 5. When finished Hardware Installation, click “Next” to proceed to next step, Network Card Selection. 6. Diagnostic screen. (If connection fails, the screen will show “FAIL”, please check your router is connected correctly.) 7. Click Next to enter Configuration Details 8.
- Page 25 10. Please configure the Wireless LAN setting and click next. (If your router does not support wireless, please ignore this screen and it will not appear.) 11. Click Next to proceed to Diagnostic screen 12. Congratulations!! You’ve completed the setup procedure and are ready for surfing the Internet.
-
Page 26: Factory Default Settings
3.3 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP server: DHCP server is enabled. -
Page 27: Lan And Wan Port Addresses
3.4 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 PPPoE function enabled to automatically get DHCP server function Enabled the WAN port configuration... -
Page 28: Configuring With Your Web Browser
Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password prompt window will appear. The default username and password are “admin” and “admin” respectively. Congratulation! You are now successfully logon to the BiPAC 5200W ADSL2+ Router! -
Page 29: Chapter 4
Advanced Setup (Firewall, Routing, NAT, QoS, ADSL) Access Management (ACL, Filter, SNMP, UPnP, DDNS) Maintenance (Administration, Time Zone, Firmware, SysRestart, Diagnositics) Status (Device Info, System Log, Statistics) Help Please see the relevant sections of this manual for detailed instructions on how to configure your Billion Router. -
Page 30: Quick Start
4.1 Quick Start For detailed instructions on configuring WAN settings, see the Interface Setup section of this manual. The Quick Start Wizard is a useful and easy utility to help setup the device to quickly connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure the password, time zone, and WAN settings of your device. - Page 31 Step1. Set your new password. Step2: Choose your time zone.
- Page 32 Step3: Set your Internet connection...
- Page 33 Step4: Save settings of this ADSL router.
-
Page 34: Interface Setup
4.2 Interface Setup Click this item to access the following sub-items that configure the ADSL2+ router: Internet, LAN, and Wireless. These functions are described in the following sections. 4.2.1 Internet... - Page 35 ATM VC ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority.
- Page 36 Static IP: Select this option to set static IP information. You will need to enter in the Connection type, IP address, subnet mask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x).
- Page 37 Multicast: IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data. The BiPAC 5200W supports both IGMP version 1 (IGMP-v1), IGMP-v2, and IGMP-v3. Select Disabled to disable it MAC Spoofing: Select Enable and enter a MAC address that will temporarily change your router’s...
-
Page 38: Lan
Multicast: IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data. The BiPAC 5200W supports both IGMP version 1 (IGMP-v1), IGMP-v2 and IGMP-v3. Select Disabled to disable it. - Page 39 TCP/IP configuration at start-up from a server. DHCP: If set to Enabled, your BiPAC 5200W can assign IP addresses, an IP default gateway and NS servers to Windows 95, Windows NT and other systems that support the DHCP client.
-
Page 40: Wireless
4.2.3 Wireless This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN. - Page 41 Access Point Settings Access Point: Default setting is set to Activated. If you do not have any wireless device in your network, select Deactivated. Channel ID: The range of radio frequencies used by IEEE 802.11b/g/n wireless devices is called a channel.
- Page 42 the bandwidth the better the performance will be. Guard Interval: Select either Auto or 800nsec for the guard interval. The guard interval is here to ensure that data transmission do not interfere with each other, it also prevents propagation delays, echoing and reflections.
- Page 43 without any data encryption Key 1 to Key 4: Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection.
- Page 44 Radius Remote Authentication Dial In User Service (RADIUS) is a networking protocol that provides centralized Authentication, Authorization, and Accounting (AAA) management for computers to connect and use a network service. RADIUS is a client/server protocol that runs in the application layer, using UDP as transport.
- Page 45 helps to protect the wireless communication. WDS Settings WDS is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed simply to define peer’s MAC address of the connected AP WDS takes advantages of cost saving and flexibility which no extra wireless client device is required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network.
-
Page 46: Advanced Setup
4.3 Advanced Setup 4.3.1 Firewall Your router includes a firewall for controlling Internet access from your LAN and helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet. -
Page 47: Routing
4.3.2 Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. #: Item number Dest IP: IP address of the destination network Mask: The destination mask address. Here mask refers to the number of the amount of ‘1’ in submask, it is the length of net-id. - Page 48 ADD Route Destination IP Address: This is the destination subnet IP address. IP Subnet Mask: A subnet mask allows IP networks to be subdivided for security and performance purposes. Gateway IP Address: This is the gateway IP address to which packets are to be forwarded. Metric: It represents the cost of transmission for routing purposes.
-
Page 49: Nat
4.3.3 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and Route Table. - Page 50 The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by the Firewall and NAT algorithms then passed to the DMZ host, when a packet received does not use a port number used by any other Virtual Server entries.
- Page 51 The reason for this is that when using NAT, your publicly accessible IP address will be used by and point to your router, which then needs to deliver all traffic to the private IP addresses used by your PCs. Please see the WAN configuration section of this manual for more information on NAT. The device can be configured as a virtual server so that remote users accessing services such as Web or FTP services via the public (WAN) IP address can be automatically redirected to local servers in the LAN network.
- Page 52 Start Port Number: Enter a port number as the beginning number of the range which you want to give to devices to access in this field. End Port Number: Enter a port number as the end number of the range which you want to give to devices to access in this field.
- Page 53 IP Address Mapping Address Mapping Rule: Shows the PVC where the rule will be applied to. Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type.
- Page 54 N/A for Server port mapping. Local End IP: This is the end range for Inside Local IP Address (ILA). If your rule is for all local IP addresses, then enter 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the Local End IP address.
-
Page 55: Qos
4.3.4 QoS Quality of Service (QoS) helps to prioritize data as it enters your router. By attaching special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based on priority. This is useful when there are certain types of data you want to give higher priority to, such as voice data packets given higher priority than Web data packets. - Page 56 Rule You can set 16 different QoS rules. Each QoS rule has its detail setting conditions like: 802.1p application, DSCP, IP, MAC, Protocol, TOS, VLAN etc, you can modify the default value to any new one you wish. Please notice that only when the packet fulfill every detail setting conditions here, then this packet will be remarked as the priority queue of each rule.
- Page 57 Destination MAC: Set the Ethernet MAC value that you want to filter in destination side. IP: Set the IP address value that you want to filter in destination side. Mask: Set the subnet mask value that you want to filter in destination side. Range: Set the port range value that you want to filter in destination side.
-
Page 58: Adsl
4.3.5 ADSL ADSL Mode: The default setting is Auto Sync-Up. This mode will automatically detect your ADSL2, ADSL2+, ADSL2, G.DMT, G.lite, and T1.413. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.DMT or T1.413 first. If it still fails, please try the other values such as ALCTL, ADI, etc. -
Page 59: Access Management
Secure IP Address: The default 0.0.0.0 allows any client to use this service to remotely manage the BiPAC 5200W. Type an IP address to restrict access to a client with a matching IP address. Application: Choose a service that you may use to remotely manage the BiPAC 5200W. -
Page 60: Filter
4.4.2 Filter You can filter the packages by IP port, MAC and Application. Filter Type Filter Type Selection: There are three types “IP/MAC Filter”, “Application Filter”, and “URL Filter” that user can select for this connection. - Page 61 IP/MAC Filter Set Editing IP/MAC Filter Set Index: This is item number Interface: Select which interface to configure, PVC or LAN. Direction: Select the access to the Internet (“Outgoing”) or from the Internet (“Incoming”).or Both. IP/MAC Filter Rule Editing IP/MAC Filter Rule Index: This is item number Rule Type: Choose “IP”...
- Page 62 Application Filter Application Filter: Select this option to Activated/Deactivated the Application filter. ICQ: Select this option to Allow/Deny ICQ. MSN: Select this option to Allow/Deny MSN. YMSG: Select this option to Allow/Deny Yahoo messenger. Real Audio/Video: Select this option to Allow/Deny Real Audio/Video. Press SAVE to apply your settings.
- Page 63 URL Filter Active: Select Yes to enable URL Filter. URL Index: This is item number. URL: llow you to prevent users on your network from accessing particular websites by their URL. Input the URL you want to filter in this field. Press SAVE to confirm your settings, and the corresponding settings will be listed in the URL Filter Listing table.
-
Page 64: Snmp
Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. BiPAC 5200W supports SNMP agent functionality which allows a manager station to manage and monitor the router through the network. -
Page 65: Upnp
Auto-configured: Select this check box to allow UPnP-enabled applications to automatically configure the BiPAC 5200W so that they can communicate through the BiPAC 5200W, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to communicate with another UPnP enabled device;... -
Page 66: Ddns
ISP. Dynamic DNS: Select this check box to use Dynamic DNS. Service Provider: www.dyndns.org My Host Name: Type the domain name assigned to your BiPAC 5200W by your Dynamic DNS provider. E-mail Address: Type your e-mail address. Username: Type your user name. -
Page 67: Maintenance
4.5 Maintenance 4.5.1 Administrator In factory setting, the default password is admin, and that for user is also password. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place. New Password: Type the new password in this field Confirm Password: Type the new password again in this field. -
Page 68: Time Zone
4.5.2 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified. -
Page 69: Firmware
To upgrade the firmware of BiPAC 5200W, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade”... -
Page 70: Sysrestart
Firmware screen. DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. warning 4.5.4 SysRestart Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration). -
Page 71: Diagnostics
4.5.5 Diagnostics The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. -
Page 72: Status
4.6 Status 4.6.1 Device Info This page displays the current information for the ADSL Router. It will display the Firmware version, LAN, WAN, and MAC address information. Device Information Firmware Version: This is the Firmware version MAC Address: This is the MAC Address... - Page 73 IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. DHCP Server: LAN port DHCP role - Enabled, Relay or disabled Virtual Circuit: There are eight groups of PVC can be defined. VPI: The valid range for the VPI is 0 to 255 VCI: The valid range for the VCI is 1 to 65535 Status: “Not connected”...
-
Page 74: System Log
4.6.2 System Log Display system logs accumulated up to the present time. You can trace historical information with this function. -
Page 75: Statistics
4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and "Receive Statistics". Ethernet Interface: This field displays the type of port Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted in the last second. - Page 76 ADSL Transmit total PDUs: This field displays the number of total PDU transmitted in the last second. Transmit total Error Counts: This field displays the number of total error transmitted in the last second. Receive total PDUs: This field displays the number of total PDU received in the last second. Receive total Error Counts: This field displays the number of total error received in the last second.
- Page 77 WLAN Tx Frames Count: This field displays the number of frames transmitted in the last second. Tx Errors Count: This field displays the number of errors frames transmitted in the last second. Tx Drops Count: This field displays the number of drops frames transmitted in the last second. Rx Frames Count: This field displays the number of frames received in the last second.
-
Page 78: Help
4.7 Help This help page provides you some useful messages such as the introductions of some concepts and some guides. When some problems are encountered, you can turn to this page for help. For example, if you don’t understand what is Quick Start, you can go to this page, click on Quick Start, then you’ll see some messages about it, and understand it quickly. -
Page 79: Chapter 5
Chapter 5 Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems with starting up the router Problem Corrective Action... -
Page 80: Problems With The Wan Interface
Problems with the WAN Interface Problem Corrective Action Initialization of the PVC Ensure that the telephone cable is connected properly from the ADSL port to the wall jack. The ADSL LED on the front connection (“line sync”) failed. panel of the router should be on. Check that your VPI, VCI, encapsulation type and type of multiplexing settings are the same as those provided by your ISP. -
Page 81: Appendix
Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion WORLDWIDE http://www.billion.com MAC OS is a registered Trademark of Apple Computer, Inc.