Main Function - ACME IM-5S-ELC User Manual

4.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are showing below:
MENU
Focus Adjust
Self-Test
Fixture Hours
Reset
DMX 512 Address Setting
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
DMX512 Address Setting
Show mode 1
Show mode 2
Show mode 3
Show mode 4
Slave Mode " Normal "
Slave mode " 2 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
Pan Inversion
Tilt Normal
Tilt Inversion
Dimmer Normal
Dimmer Inversion
LED on
LED off
Display Normal
Display Inversion
is showing on the display. Pressing ENTER
9J
Stand by Blackout the unit
Strobe
1.Gobo / Color
sync.
Function strobe
Move
2.Sync. strobe
Spot
3.Two-light strobe
Sound 1
Mode (LED off )
Stand by Blackout the unit
Strobe
1.Color sync.
strobe
Function 2.Sync. strobe
Move
3.Two-light strobe
Wash
Sound 1
Mode (LED off )
5.3.1 iSolution Operation
♦
Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦
DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦
Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
X/Y moving show Color/Gobo X/Y moving setting
mode selection selection 1.Pan position
( Show 1 ~ Show 1. Hold on for gobo 2.Tilt position
4 ) change. First set Master
Please refer to 2. Press shortly for unit, then set Slave
Show mode in color change units' position
4.2 Main Function
Sound 2 Slow/Sound 3 Position/ Latch
(LED normal (LED on) (LED fast blinking)
blinking)
X/Y moving show Color selection X/Y moving setting
mode selection 1.Pan position
( Show 1 ~ Show 2.Tilt position
4 ) 3.Dimmer
Please refer to First set Master
Show mode in unit, then set Slave
4.2 Main Function units' position
Sound 2 Slow/Sound 3 Position/ Latch
(LED normal (LED on) (LED fast blinking)
blinking)
is showing on the display. Pressing ENTER
14J