Related Manuals for ACME LITE PANEL 900 LP-900 WW BD30
Summary of Contents for ACME LITE PANEL 900 LP-900 WW BD30
-
Page 1: User Manual
LP-900 WW BD30 LP-900 CW BD30 User Manual Please read the instructions carefully before use... -
Page 2: Table Of Contents
CONTENTS 1. Safety Introductions ....................2 2. Technical Specifications ..................3 3. How To Set The Fixture ..................4 3.1 Control Panel ....................4 3.2 Main Function ....................5 4. How To Control The Unit ..................8 4.1 Master/Slave Function ..................8 4.2 DMX Controller .................... -
Page 3: Safety Introductions
1. Safety Introductions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ... -
Page 4: Technical Specifications
Caution: There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. Installation: The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. -
Page 5: How To Set The Fixture
Color Temperature: 2800 ~ 3200K 6500 ~ 7000K CRI: ≥ 82 Weight: 6.2Kgs Dimension: 371 x 328 x 111mm 3. How To Set The Fixture 3.1 Control Panel hows the various menus and the selected functions; Display: 2. -
Page 6: Main Function
POWER Power On 3. Button: MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions ENTER To confirm the selected functions 4. Dimmer Adjust knob: Adjusts the lightness for the unit; 5. - Page 8 DMX 512 Address To select , press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP buttons to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup or automatically exit menu mode without any change after 30 seconds. To go back to the previous functions without any change press the MENU button.
-
Page 9: How To Control The Unit
Display Inverse To select , press the ENTER button to show DISPLAY on the display. Press the ENTER button again and it will show the (inversion). To go back to the functions without any change press MENU button. Auto Test To select , press the ENTER button to show TEST on the display and the unit will run a self-test. -
Page 10: Dmx Controller
should set the master unit effect via its knobs, then the other units (slave) will lighting as the same. 4.2 DMX Controller When using a universal DMX controller to control the units, you must set a DMX address from 1 to 512. -
Page 11: Dmx512 Connections
6. DMX512 Connections The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system 2. -
Page 12: Troubleshooting
7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. -
Page 15: Declaration Of Conformity
Declaration of Conformity We declare that our products (lighting equipment) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1: 2009 ; EN55103-2: 2009; EN62471: 2008; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008. &... - Page 16 Innovation, Quality, Performance...
Need help?
Do you have a question about the LITE PANEL 900 LP-900 WW BD30 and is the answer not in the manual?
Questions and answers