Huawei AR1200 series Configuration Manual page 371
Enterprise routers
Hide thumbs
Also See for AR1200 series:
- Configuration manual (342 pages) ,
- User configuration manual (232 pages) ,
- Hardware description (218 pages)
Table of Contents
Advertisement
Huawei AR1200 Series Enterprise Routers
Configuration Guide - VPN
[Huawei-Tunnel0/0/0] ip address 172.16.1.1 255.255.255.0
[Huawei-Tunnel0/0/0] tunnel-protocol gre p2mp
[Huawei-Tunnel0/0/0] source ethernet 1/0/0
[Huawei-Tunnel0/0/0] nhrp redirect
[Huawei-Tunnel0/0/0] nhrp entry multicast dynamic
# Configure a tunnel interface and an NHRP mapping entry of the hub, and enable NHRP shortcut
on Spoke1.
[Huawei] system-view
[Huawei] interface tunnel 0/0/0
[Huawei-Tunnel0/0/0] ip address 172.16.1.101 255.255.255.0
[Huawei-Tunnel0/0/0] tunnel-protocol gre p2mp
[Huawei-Tunnel0/0/0] source ethernet 1/0/0
[Huawei-Tunnel0/0/0] nhrp shortcut
[Huawei-Tunnel0/0/0] nhrp entry 172.16.1.1 44.1.1.1 register
# Configure a tunnel interface and an NHRP mapping entry of the hub, and enable NHRP shortcut
on Spoke2.
[Huawei] system-view
[Huawei] interface tunnel 0/0/0
[Huawei-Tunnel0/0/0] ip address 172.16.1.102 255.255.255.0
[Huawei-Tunnel0/0/0] tunnel-protocol gre p2mp
[Huawei-Tunnel0/0/0] source ethernet 1/0/0
[Huawei-Tunnel0/0/0] nhrp shortcut
[Huawei-Tunnel0/0/0] nhrp entry 172.16.1.1 44.1.1.1 register
Step 5 Verify the configuration.
After the preceding configurations are complete, check the NHRP mapping entries on Spoke1
and Spoke2.
Run the display nhrp peer all command on Spoke1, and the command output is as follows.
[Huawei] display nhrp peer all
-------------------------------------------------------------------------------
Protocol-addr
-------------------------------------------------------------------------------
172.16.1.1
-------------------------------------------------------------------------------
Tunnel interface: Tunnel0/0/0
Created time
Expire time
Run the display nhrp peer all command on Spoke2, and the command output is as follows.
[Huawei] display nhrp peer all
-------------------------------------------------------------------------------
Protocol-addr
-------------------------------------------------------------------------------
172.16.1.1
-------------------------------------------------------------------------------
Tunnel interface: Tunnel0/0/0
Created time
Expire time
On the hub, check the NHRP mapping entries on Spoke1 and Spoke2.
Run the display nhrp peer all command on the hub, and the command output is as follows.
[Huawei] display nhrp peer all
-------------------------------------------------------------------------------
Protocol-addr
-------------------------------------------------------------------------------
172.16.1.101
Issue 01 (2012-04-20)
Mask
NBMA-addr
32
44.1.1.1
: 2011.08.18-15:10:26
: --
Mask
NBMA-addr
32
44.1.1.1
: 2011.08.18-15:12:53
: --
NOTE
If you run the display nhrp peer all command on Spoke1 and Spoke2, you can view only the NHRP
mapping entry of the hub.
Mask
NBMA-addr
32
44.3.1.2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
NextHop-addr
Type
172.16.1.1
static
NextHop-addr
Type
172.16.1.1
static
NextHop-addr
Type
172.16.1.101
dynamic
6 DSVPN Configuration
Flag
hub
Flag
hub
Flag
route tunnel
360
Hide quick links:
Advertisement
Table of Contents
