Symbols; Duty Cycle; Measurement Applications - Klein Tools CL800 Instruction Manual

enGliSH
electrical SpecificationS
frequency (auto-ranGinG)
9.999Hz 0.001Hz
99.99Hz 0.01Hz
999.9Hz 0.1Hz
9.999kHz 1Hz
99.99kHz 10Hz
500.00kHz 100Hz
Sensitivity: > 8V RMS
Maximum input: 600V DC or 600V AC RMS

Duty cycle

1% to 99.9% 0.1%
pulse width: 0.1 – 100ms
frequency width: 5Hz to 10kHz
Sensitivity: >8V RMS
Maximum input: 600V DC or 600V AC RMS
otHer MeaSureMent applicationS
Maximum input: 600V AC RMS or 600V DC
• Diode test: Max. 1.5mA, open circuit voltage ~3.0V DC
• continuity check: Audible signal <50Ω, test current <0.35mA
• Sampling frequency: 3 samples per second
• low impedence (low Z): Input impedence >3kΩ
Max input 600V RMS
• auto power off: After ~30 minutes of inactivity
• overload: "OL" indicated on display, overload protection
1000V in Voltage setting, 600V RMS in all other settings
• polarity: "-" on display indicates negative polarity
• Display: 3-5/6 digit, 6000 Count LCD
WarninGS
to ensure safe operation and service of the meter, follow these
instructions. failure to observe these warnings can result in
severe injury or death.
• Before each use verify meter operation by measuring a known
voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Use only with CAT IV rated test leads.
4
CL800-1390106ART.indd 4-5
Dwg Name: CL800-1390106ART
Dwg No: 1390106
ECO No: 20622
Pkg Dwg Ref: 1290186
Color Reference: N/A
±(1.0% + 5 digits)
±(1.2% + 2 digits)
Rev: A
WarninGS
• Ensure meter leads are fully seated, and keep fingers away from
the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes are
connected.
• Use caution when working with voltages above 25V AC RMS or
60V DC. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock, replace
batteries when a low battery indicator appears.
• Do not attempt to measure resistance or continuity on a live
circuit.
• Always adhere to local and national safety codes. Use personal
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
SyMbolS on Meter
ac
resistance (in ohms)
Double insulated class ii
Diode
Hz
frequency
°F/°C
temperature (fahrenheit / celsius)
V Voltage (Volts)
Warning or caution
To ensure safe operation and service of this meter, follow all
warnings and instructions detailed in this manual.
risk of electrical Shock
Improper use of this meter can lead to risk of electrical shock. Follow
all warnings and instructions detailed in this manual.
risk of electrical Shock
Application around and removal from UNINSULATED HAZARDOUS
LIVE conductors is permitted.
SyMbolS on lcD
ac Measurement
negative reading
auto ranging
Min Minimum Value Hold
auto power off
Diode test
M Mega (value x 10 )
6
μ micro (value x 10 )
-6
ohms
A
amps
Hz frequency (Hertz)
°F
Degrees (fahrenheit)
Dwg Name: CL800-1390106ART
Dwg No: 1390106
ECO No: 20622
Pkg Dwg Ref: 1290186
Color Reference: N/A
ac/Dc
audible continuity
Ground
capacitance
%
Duty-cycle
low impedance
a amperage (amps)
Dc Measurement
Data Hold
MaX Maximum Value Hold
low battery
audible continuity
k kilo (value x 10 )
3
m mili (value x 10 )
-3
n nano (value x 10 )
-9
V Volts
F
farads
% Duty cycle
°C
Degrees (celsius)
5
9/24/2015 2:39:58 PM
Rev: A