Dial Menu; Preset Menu - Sony PCM-7040 Operation Manual

7-3 Dial Menu Operations

7-3-4 Dial Menu

Preset menu

in Pt (IN POINT)
out Pt (OUT POINT)
GAin rnG (GAIN RANGE)
inP GAin (INPUT GAIN)
croS FAdE (CROSS FADE TIME)
SPot Ers (SPOT ERASE)
Display menu
Error (ERROR CODE)
cAution (CAUTION CODE)
Au rEF (AUDIO LEVEL)
Au rEF–P (AUDIO PEAK LEVEL)
dAtE YEAr (DATE(YYYY:MM:DD))
dAtE Hour (DATE(HH:MM:SS))
[dSP Grd] (DISPLAY GRADE)
bASic
EnHAncEd
LASt Err
Ecc
tAPE tcF (TAPE TC FORMAT)
Hour–t
Setup menu
– –Sto– – (STORE)
– –rcL– – (RECALL)
– –SEtuP– – (POWER ON SETUP)
dAtE SEt (DATE SET)
rS-232 (RS-232C MODE)
tc bASE (TIME CODE BASE)
rEF tcF (REFERENCE & TC FORMAT)
rEc tc (REC TC)
PrE EP (PRE-EMPHASIS)
din SYnc (DIN SYNC)
SYnc nrr (SYNC LOCK RANGE)
rE–cHASE (RE-CHASE MODE)
cHASE–Au (CHASE AUDIO)
cHASE–S (CHASE KEY MODE)
orG codE (ORIGIN CODE)
dAtE rEc (DATE REC)
diSP [1] (DISPLAY KEY MENU [1])
diSP [2] (DISPLAY KEY MENU [2])
[SEt Grd] (SETUP MENU GRADE)
EnHAncEd
bASic
[SEt tc] (SETUP TC MENU)
FrEErun
cLoSE oPEn
GEn out
tc rEGEn
rEc ub
tc dLY
ELAPSE
7-6
Chapter 7 Menu Operations
(LAST ERROR POINT)
(ECC LOG)
(HOUR TIME)
(TC GENERATOR MODE)
(TC OUTPUT)
(INPUT TC REGENERATE)
(REC U-BIT)
(TC DELAY)
(ELAPSE MODE)
[SEt id] (SETUP ID MENU)
id rEc (REC ID)
cLoSE oPEn
S–id Auto (ID AUTO REC)
LSYnc tH (LEVEL SYNC THRESHOLD)
LSYnc bt (LEVEL SYNC BLANK TIME)
Auto StoP (AUTO STOP)
Auto SrcH (AUTO ID SEARCH)
PrEroLL (PREROLL)
rEno SPd (RENUMBER SPEED)
[SEt SYS] (SETUP SYSTEM MENU)
coPY id
cLoSE oPEn
SYncPb
rLb StoP
Ed cHASE (EDIT CHASE)
9P rEcHS
iS dFLt
iS dLY–t
LocAL
r-8Pin
37 out-10
37 out-14
37 out-18
37 in-33
37 in-34
37 in-35
37 joG
inPut–S
PAnEL–S
AFtr cuE
rEc dFLt
Auto in P
PuncH io
AtF SEnS
[SEt dSP] (SETUP DISPLAY MENU)
FL diSP (DIMMER)
cLoSE
oPEn
P–HoLd (PEAK HOLD MODE)
o–HoLd (OVER HOLD MODE)
HoLd–t (PEAK HOLD TIME)
rLS–t (RELEASE TIME)
o–SEnS (OVER LEVEL SENSITIVITY)
[SEt SP] (SETUP SP MENU)
Pb cond
cLoSE oPEn
E–HoLd
E–trSHLd
[SEt Ed] (SETUP EDIT MENU)
JoG LooP (JOG LOOPING)
cLoSE oPEn
StArt (MEMORY MODE)
JoG ctL (MEMORY JOG CONTROL)
1St Edit (FIRST EDIT)
tc rtn (TIME CODE MISSING RETURN)
Edit rtn (EDIT RETURN)
[SEt rS] (SETUP RS-232C MENU)
bAud rAtE (BAUD RATE)
cLoSE
oPEn
PAritY (PARITY BIT)
dAtA (DATA BITS)
(COPY ID)
(SYNC PB)
(ROLLBACK STOP)
(9PIN RECHASE MODE)
(POWER ON MEMORY START
MODE)
(MEMORY START DELAY)
(LOCAL ENABLE)
(8PIN REMOTE MODE)
(37pin RESERVED STATUS)
(37pin ALARM STATUS)
(37pin SERVO STATUS)
(37pin CHASE COMMAND)
(37pin EJECT COMMAND)
(37pin RESERVED COMMAND)
(37pin MEMORY JOG)
(INPUT MONITOR KEY)
(FRONT PANEL KEY)
(AFTER CUE MODE)
(POWER ON REC MODE)
(AUTO INPUT)
(PUNCH IN/OUT)
(ATF SERVO SENSITIVITY)
(PB CONDITION TALLY)
(ERROR HOLD)
(ERROR THRESHOLD)