Table of Contents
Advertisement
Index
Selecting the peak level hold time of the
level meters (PEAK HOLD TIME)
7-12
Selecting the release time for the level
meters (RELEASE TIME) 7-12
LEVEL SYNC THRESHOLD 7-9
Loading 3-11
LOCAL ENABLE 7-10
Locate
Locating specific points on a tape 5-2
Setting the locate point 5-3
Start ID locate 5-4
LOCATE key and indicator 2-4
LOCATE POINT 5-3
LOCATE POINT (Program number) 5-5
Location and function of parts and controls
Connector panel (rear) 2-9
Display 2-6
Front panel 2-1
M, N
MARK key 2-4
Memory jog 6-4
MEMORY JOG CONTROL 7-13
MEMORY MODE 7-13
Memory start
Outputting playback signals
immediately after pressing the PLAY
key 6-4
Selecting the duration (delay time) to
output the sound after pressing the
PLAY key for memory start playback
(MEMORY START DELAY) 7-10
Selecting whether or not to activate the
memory start when you turn the
power on (POWER ON MEMORY
START MODE) 7-10
MEMORY START DELAY 7-10
MEMORY START key and indicator 2-3
Menus (general description) 7-1
MONITOR output connectors 2-10
MUTE indicator (When the MUTE
indicator comes on) 9-1
O
OVER HOLD MODE 7-12
OVER LEVEL SENSITIVITY 7-12
P, Q
PB CONDITION TALLY 7-12
PB CONDITION (When the PB
CONDITION indicator comes on) 9-1
PDP-15, PDP-34, PDP-48, PDP-64, PDP-
94, PDP-124 A-2
PEAK HOLD MODE 7-12
PEAK HOLD TIME 7-12
Playback
Controlling the playback speed—
Variable-speed playback 6-1
I-2
Index
Outputting playback signals
immediately after pressing the PLAY
key—Memory start function 6-4
Playback procedure 5-1
Selecting the timing of sound output
when chasing (CHASE AUDIO) 7-9
Time code repeat playback 5-3
Power supply 3-8
PRE-EMPHASIS 7-8
Preset menu
Preset menu 7-7
Preset menu operation 7-5
POWER ON MEMORY START MODE
7-10
POWER ON REC MODE 7-11
POWER ON SETUP 7-8
POWER switch 2-1
Program number
Renumbering program numbers 4-12
Writing the program number 4-11
Punching-in/Punching-out during
rechasing 6-10
PREROLL 7-10
R
RE-CHASE MODE 7-8
REC ID 7-9
REC INH (When the REC INH indicator
comes on) 9-1
REC TC 7-8
REC U-BIT 7-9
RECALL 7-7
Recommended equipment and optional
accessories A-2
Recording
Controlling the recording level 4-4
Controlling the Recording
Speed-Variable-Recording Speed 6-2
Record mode select keys and indicators
2-4
Recording 4-1
Recording procedure 4-4
Selecting the audio output signals 4-1
Selecting the recording mode 4-1
REF VIDEO input section 2-9
REFERENCE & TC FORMAT 7-8
RELEASE TIME 7-12
REMOTE connector
37P (D-SUB 37-pin) 2-10
9P (D-SUB 9-pin) 2-11
8P (DIN 8-pin) 2-11
REMOTE(9P)/LOCAL selector 2-1
Renumbering Program numbers 4-12
RM-D7100 A-2
RMM-30 A-2
RMM-31 A-2
ROLLBACK STOP 7-10
RS-232C Computer interface connector
2-11
S
SAMPLING FREQ selector 2-2
Sampling frequency
Sampling frequency indicator 2-6
Selecting the sampling frequency 3-9
Search dial 2-4
Searching for unrecorded part 5-5
Selecting hold mode of the MUTE
indicator and PB CONDITION indicator
(ERROR HOLD) 7-13
Selecting how to release chase operation
mode (CHASE KEY MODE) 7-9
Selecting memory mode at memory start
(MEMORY MODE) 7-13
Selecting recording mode to be set at
power-on (POWER ON REC MODE)
7-11
Selecting recording time code (REC TC)
7-8
Selecting the baud rate (BAUD RATE)
7-13
Selecting the chase mode (RE-CHASE
MODE) 7-8
Selecting the copy ID which will be
recorded within the main ID (COPY ID)
7-10
Selecting the input signal 3-9
Selecting the level detection sensitivity
that lights the "OVER" segments of the
level meters (OVER LEVEL
SENSITIVITY) 7-12
Selecting the level meter peak hold mode
(PEAK HOLD MODE) 7-12
Selecting the menu level of the display
menu (DISPLAY GRADE) 7-7
Selecting the setup menu level for signal
processing (SETUP MENU) 7-12
Selecting the setup menu level for the
editor (SETUP EDIT MENU) 7-13
Selecting the setup menu level for the
system control (SETUP SYSTEM
MENU) 7-10
Selecting the state that turns on the PB
CONDITION indicator (PB
CONDITION TALLY) 7-12
Selecting the time code format and the
reference video signal frequency
(REFERENCE & TC FORMAT) 7-8
Selecting whether the first edit is
performed from a BVE series video
editor (1ST EDIT) 7-13
Selecting whether to accept the command
from the unit's panel, 37-pin parallel
remote signal connector and 8-pin
parallel remote signal connector in
remote mode (LOCAL ENABLE) 7-10
Selecting whether to automatically call
setup from the setup menu at power-on
(POWER ON SETUP) 7-8
- Quick Links:
- Specifications
Hide quick links:
Advertisement
Table of Contents
