Sony PCM-7040 Operation Manual page 90

Selecting whether to automatically locate a
start ID when a cassette is inserted
(AUTO ID SEARCH) 7-10
Selecting whether to automatically locate a
start ID when detecting a skip ID
(AUTO STOP) 7-10
Selecting whether to automatically reset
the elapse time when detecting the start
ID (ELASPE MODE) 7-9
Selecting whether to loop at the end of the
sound stored in memory at memory jog
(JOG LOOPING) 7-13
Selecting whether to perform the muting
when the error rate increases (ERROR
THRESHOLD) 7-13
Selecting whether to record in monitor
recording mode or in sync recording
mode 4-1
Selecting whether to send the TIME
CODE MISSING message upon
receiving the CURRENT TIME SENSE
command (TIME CODE MISSING
RETURN) 7-13
SERVO (When the SERVO lock indicator
goes off) 9-1
Setting and displaying the input signal
gain 4-5
Setting back to the factory-set status 7-2
Setting the display back to the default
condition 7-2
Setting whether to preroll-stop before the
point where an ID is written at start ID
locating or program-number locating
(PREROLL) 7-10
Setup menu
Setup menu list 7-7
Setup menu operation 7-5
Storing customized data for the setup
menu (STORE) 7-7
SETUP DISPLAY MENU 7-12
SETUP EDIT MENU 7-13
SETUP MENU for signal processing 7-12
SETUP MENU GRADE 7-9
SETUP RS-232C MENU 7-13
SETUP SYSTEM MENU 7-10
SETUP TC MENU 7-9
Specifications A-1
Spot erase 6-6
STANDBY key 2-3
Start ID
Erasing an ID 4-11
Selecting whether to automatically write
the Start ID or not during assemble
recording (ID AUTO REC) 7-9
Start ID write/erase indication 2-7
Writing an ID 4-10
START ID keys 2-4
STORE 7-7
Subcode data 4-2
SYNC LOCK RANGE 7-8
SYNC PB 7-10
SYNC signal selector 2-2
Synchronization
Chase synchronized operation 6-7
External sync data A-1
Lock range indicator 2-8
Selecting the lock frequency range in
external synchronization mode
(SYNC LOCK RANGE) 7-8
Selecting whether to synchronize the
playback time code with the phase of
the input video signal during playback
(SYNC PB) 7-10
Sync signal indication 2-7
SYNC signal selector 2-2
T
Tape
Displaying the tape run time (ELASPE)
7-4
Selecting whether to accept the
command from the tape transport
control keys or not when playing back
in the local mode (FRONT PANEL
KEY) 7-11
Tape playback speed variable range
A-1
Tape recording format A-1
TAPE TC FORMAT 7-7
Tape time display area 2-6
TC DELAY 7-9
Time code
Displaying the internal generator time
code (GEN TIME CODE) 7-4
Displaying the time code format of the
tape (TAPE TC FORMAT) 7-7
Displaying the time code input to the
unit (EXT TIME CODE) 7-4
Repeat playback 5-3
Selecting the basis of the time code
(TIME CODE BASE) 7-8
Selecting the operation mode of the
internal time code generator (TC
GENERATOR MODE) 7-9
Selecting the setup menu level for the
time code (SETUP TC MENU) 7-9
Selecting the time code format and the
reference video signal frequency
(REFERENCE & TC FORMAT) 7-8
Selecting the time code output (TC
OUTPUT) 7-9
Selecting whether to apply the phase
adjustment of the time code output to
the analog audio signals or digital
audio signals (TC DELAY) 7-9
Selecting whether to regenerate the
external time code or not (INPUT TC
REGENERATE) 7-9
Setting the start time value 4-8
Time code indication 2-7
Time code mode indicator 2-8
TIME CODE BASE 7-8
TIME CODE input/output section 2-9
TIME CODE MISSING RETURN 7-13
U
U-BIT 7-4
Unloading 3-11
User bit
Displaying the user bit of the external
time code input to the unit (EXT U-
BIT) 7-4
Displaying the user bit of the internal
generator time code (GEN TIME
CODE) 7-4
Displaying the user bit on the playback
tape (U-BIT) 7-4
Selecting the use bit when recording
(REC U-BIT) 7-9
Setting the user bit 4-9
V
VARI SPEED 6-1
VARI SPEED key 2-4
Variable-speed (VARI-SPEED) playback
–0.1% playback with a film based-
system 6-1
–0.1% playback with an HDVS-based
system 6-1
Controlling the playback speed 6-1
Setting the playback speed to the normal
speed 6-1
Setting the variable speed value and
display of the set value 6-1
Variable-Speed Recording
+0.1% recording with a film-based
system 6-2
-0.1% recording with an HDVS-based
system 6-3
Using an AES/EBU-format signal or
word sync signal outside of ±100ppm
as the sync signal 6-2
W, X, Y, Z
Warning
Displaying the warning code
(CAUTION CODE) 7-7
Flashing indicators 9-5
Operating error warnings 9-6
Warning indicators 2-3
Word sync signal 2-2, 3-10
WORD SYNC signal input/output section
2-10
Index
I-3