Panasonic DVCPRO50 AJ-D960EG Operating Instructions Manual page 82

Setup menus
USER menu
<AUDIO>
No.
733
734
735
736
737
750
751
The underline on the setting item denotes the initial setting.
<Concerning the CUE output in the search mode>
The table below shows how the CUE output to the monitor and main signal system outputs differs according to how the setup menu item
(No. 721, No. 731 and No. 735) settings are combined.
731 721
CUE OUT MONI CH MON AUTO
SEL SEL
MANU
OFF
AUTO1
|
AUTO21
MANU
ON
AUTO1
|
AUTO21
<Notes>
• PCM audio signal output is muted when the VTR is played outside the –1 to +2.0 normal speed.
• When either AUTO1 or AUTO11 is selected, the PCM audio signal is output within –1 to +2.0 normal speed even in the automatic CUE output
mode.
(continued)
Item Setting
Superimposed Superimposed
No.
display
CUE OUT 0000
0001
MONI SEL 0000
INH 0001
0002
MON AUTO 0000
SEL 0001
0002
AUDIO PB 0000
VR 0001
JOG PROC 0000
0001
DV PB ATT 0000
0001
REC PT 0000
MUTE 0001
735 Monitor output
Lch
SEL
L/R
L PCM
R
L/R CUE
L CUE
R PCM
L/R
L PCM
R
L/R CUE
L CUE
R PCM
display
For selecting the output from the CUE OUT connector.
NORMAL
0: The timing is aligned with the output picture.
DIRECT
1: Whatever has been recorded on the tape is output with no delay.
<Note>
When "1" (DIRECT) has been selected, the timing of the out-
put picture and that of the cue output are not aligned properly.
However, this setting is effective only during DVCPRO (25
Mbps) mode playback.
This selects whether the operation of the MONITOR SELECT
OFF
button on the front panel is to be enabled or disabled.
ON
0: Operation is enabled.
ON1
1: Operation is disabled.
2: Operation is disabled in the FULL display mode and
enabled only in the FINE display mode.
Although CUE is automatically output to the monitor output in
L/R
accordance with the operation mode when a setting other
L
than MANU has been selected by setup menu item No. 721
R
(MONI CH SEL), the MON AUTO SEL setup menu item is
used to select the monitor channel which is to be auto-
matically switched to CUE.
0: CUE is output to both the left and right channels.
1: CUE is output to the left channel only.
2: CUE is output to the right channel only.
This selects whether the playback level controls are to func-
DIS
tion in the EE mode when INT SG has been selected as the
ENA
setup menu item No. 700 (INT SG) setting.
0: The INT SG output level is fixed at UNITY.
1: The INT SG output level can be varied using the playback
level controls.
Selects the digital audio output slow signal processing in the
OFF
JOG/VAR/SHTL mode.
ON
0: The sound from the digital audio without the slow signal
processing is output even in the STILL mode.
1: The sound from the digital audio output after the slow
signal processing is output.
OFF This selects the audio output level during DV playback.
0: The audio output level is not attenuated.
ON
1: The audio output level is attenuated (reduced).
This selects whether to mute the sound where recordings are
OFF
joined during DV/DVCAM playback.
ON
0: The sound is not muted.
Main signal system output
Rch CH1
PCM
PCM
CUE
PCM
CUE
PCM PCM
CUE CUE
PCM CUE
CUE PCM
82 (E)
Description
1: The sound is muted.
CH2 CH3
PCM PCM
PCM PCM
CUE CUE
PCM CUE
CUE PCM
CH4
PCM
PCM
CUE
PCM
CUE