Panasonic DVCPRO50 AJ-D960EG Operating Instructions Manual page 81

Setup menus
USER menu
<AUDIO>
No.
726
727
728
729
730
731
732
The underline on the setting item denotes the initial setting.
(continued)
Item Setting
Superimposed Superimposed
No.
display display
REC CUE 0000
0001
0002
0003 CH1+2
0004
0005
0006 CH3+4
0007 CH1–4
PB FADE 0000
0001
0002
EMBEDDED 0000
AUD 0001
MONITOR 0000
MIX L 0001 CH1+2
0002 CH3+4
0003 CH1+3
0004 CH2+4
MONITOR 0000
MIX R 0001 CH1+2
0002 CH3+4
0003 CH1+3
0004 CH2+4
CUE OUT 0000
SEL 0001
CUE SLOW 0000
0001 LINEAR
81 (E)
CUE This selects the input signal recorded in CUE.
0: CUE IN
CH1
1: Audio CH1 input
CH2
2: Audio CH2 input
3: Audio CH1 and CH2 MIX signal
CH3
4: Audio CH3 input
5: Audio CH4 input
CH4
6: Audio CH3 and CH4 MIX signal
7: Audio CH1, CH2, CH3 and CH4 mixed signals
<Note>
The input signal is fixed at cue at all times regardless of this
setup menu's setting if "SDTI" has been selected by the
INPUT SELECT switch.
AUTO This selects the processing method for the audio edit points
(IN point, OUT point) during playback.
CUT
0: According to the status during recording.
FADE
1: Forced CUT
2: Forced FADE
This selects whether to superimpose the audio data onto the
OFF
serial output.
ON
0: Data is not superimposed.
1: Data is superimposed.
OFF This makes it possible to select mixed signals for the monitor
output.
0: No mixing.
1: CH1 and CH2 are mixed and output to the left channel.
2: CH3 and CH4 are mixed and output to the left channel.
3: The CH1 and CH3 signals are mixed and output to the left
channel.
4: The CH2 and CH4 signals are mixed and output to the left
channel.
This makes it possible to select mixed signals for the monitor
OFF
output.
0: No mixing.
1: CH1 and CH2 are mixed and output to the right channel.
2: CH3 and CH4 are mixed and output to the right channel.
3: The CH1 and CH3 signals are mixed and output to the right
channel.
4: The CH2 and CH4 signals are mixed and output to the right
channel.
OFF This selects whether or not the cue signal is to be output to the
main line output in the search mode.
ON
0: CUE is not output.
1: CUE is output.
(This applies only when setup menu No. 721 (MONI CH
SEL) is not set to "MANU".)
<Notes>
1. This function works only when a setting other than MANU has
been selected by setup menu item No. 721 (MONI CH SEL).
2. The main signal system output channels used for the CUE
output differ depending on the setting selected by setup
menu item No. 735 (MON AUTO SEL).
When L/R is selected: CUE is output to CH1 to CH4.
When L is selected:
When R is selected:
For selecting the tape travel status (cue track playback status)
STEP
during slow-motion playback.
0: The output picture takes precedence, and the tape travels
at the STEP speed.
1: The cue track playback takes precedence and the tape
travels at the linear playback speed.
<Notes>
When "1" (LINEAR) has been selected:
• Set the TC/CTL switch to the TC position because the CTL
counter may not function properly.
• The picture may not appear as clearly as in the STEP mode.
Description
CUE is output to CH1 and CH3.
CUE is output to CH2 and CH4.