Panasonic DVCPRO50 AJ-D960EG Operating Instructions Manual page 119

Specifications
Video Output Connector
Analogue component output:
Analogue composite output:
Serial digital component output:
SDTI output (option):
Video Signal Adjustment
Composite video input signal:
Video output gain:
Video output chroma gain:
Video output chroma phase:
Video output black level:
Video output sync phase:
Video output SC phase:
AUDIO
Digital Audio
Sampling frequencies:
Quantizing:
Frequency response:
Dynamic range:
Distortion:
Crosstalk:
Wow & flutter:
Headroom:
Emphasis:
Cue Track
Frequency response:
Audio Input Connector
Analogue input
(CH1/CH2/CH3/CH4):
Digital input (CH1/CH2, CH3/CH4): XLR
Serial digital input:
Cue track input:
Audio Output Connector
Analogue output
(CH1/CH2/CH3/CH4):
Digital output
(CH1/CH2, CH3/CH4):
Serial digital output:
Cue track output:
Monitor output:
Headphones:
Other Input/Output Connectors
Time code input:
Time code output:
RS-422A input:
RS-422A output:
RS-232C:
Parallel input/output:
Encoder remote:
Weight and dimensions when shown are approxlmately.
Speclilcailons are subject to change without notice.
BNC 3 (Y, P , P )
B R
Y; 1.0 Vp-p, 75
P /P ; 0.7 Vp-p, 75 (100% colour bar, 0% black level)
B R
BNC 3, video 1, video 2 (video/WFM selectable), video 3 (superimpose on/off)
BNC 3, complies with SMPTE 259M-C/EBU Tech.3267-E standard, SDI 1, SDI 2, SDI 3,
(superimpose on/off)
BNC 1, complies with SMPTE 305M/321M standard (also serves as SDI1 output
connector)
3 dB
3 dB
3 dB
30
100 mV
15 sec
180
48 kHz (synchronous with video)
16 bits
20 Hz to 20 kHz 1.0 dB (at the reference level)
Better than 90 dB (1 kHz, emphasis OFF, "A" weighted)
Less than 0.05% (1 kHz, emphasis OFF, reference level)
Less than –80 dB (1 kHz, between 2 channels)
Below measurable limit
625i; 18 dB
525i; 20 dB
T1 = 50 sec, T2 = 15 sec (on/off selectable)
300 Hz to 6 kHz 3.0 dB
XLR 4, 600 /high impedance selectable (factory setting: 600 ),
+4/0/–20 dBm selectable*
2, AES/EBU format
Complies with SMPTE 259M-C, 272M/EBU Tech.3267-E (BNC
XLR 1, 600 /high impedance selectable (factory setting: 600 ),
+4/0/–20/–60 dBm selectable*
XLR 4, low impedance, +4/0/–20 dBm selectable (with 600
XLR 2, AES/EBU format
Complies with SMPTE 259M-C, 272M-A/EBU Tech.3267-E (BNC
XLR 1, low impedance, +4/0/–20 dBm selectable (with 600
XLR 2, low impedance, +4/0/–20 dBm selectable (with 600
Variable level, 6.5 mm, 8
XLR 1, 0.5 to 8 Vp-p, 10 k
XLR 1, low impedance, 2.0 0.5 Vp-p (with 600
D-sub 9-pin, RS-422A interface
D-sub 9-pin, RS-422A interface
D-sub 25-pin, RS-232C interface
D-sub 25-pin
D-sub 15-pin
119 (E)
1, 75 )
load)*
1, 75 )
load)*
load)*
load)
* EG model is fixed to –3 dBu.