Setting Application Macros - Siemens SINAMICS V20 Compact Operating Instructions

Description
P1047[0] MOP ramp-up time of the RFG
P1048[0] MOP ramp-down time of the RFG
P1074[0] BI: Disable additional setpoint
P2010[0] USS/MODBUS baudrate
P2011[0] USS address
P2012[0] USS PZD length
P2013[0] USS PKW length
P2014[0] USS/MODBUS telegram off time
P2021[0] MODBUS address
P2022[0] MODBUS reply timeout
P2023[0] RS485 protocol selection
P2034 MODBUS parity on RS485
P2035 MODBUS stop bits on RS485
P2200[0] Enable PID controller
P2216[0] Fixed PID setpoint mode
P2220[0] BI: Fixed PID setpoint select bit 0
P2221[0] BI: Fixed PID setpoint select bit 1
P2222[0] BI: Fixed PID setpoint select bit 2
P2253[0] CI: PID setpoint
P2264[0] CI: PID feedback
3.2.4

Setting application macros

Functionality
This menu defines certain common applications. Each application macro provides a set of parameter settings for a specific
application. After you select an application macro, the corresponding settings are applied to the inverter to simplify the
commissioning process.
Application macro specific parameters
Parameter Description
P1080[0] Minimum frequency
P1300[0] Control mode
P1110[0] BI: Inhibit negative
frequency setpoint
P1200[0] Flying start
P1210[0] Automatic restart
P1120[0] Ramp-up time
P1121[0] Ramp-down time
P1312[0] Starting boost
P1311[0] Acceleration boost
P1310[0] Continuous boost
SINAMICS V20 Inverter
A5E37281078-003, 05/2016
Default values for connection macros (Cn...)
001 002 003
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
Factory Default for application macro
default
AP010 AP020 AP021 AP030
0 15 20
0 7 7
0 1 -
0 - 2
1 2 2
10 10 10
10 10 20
0 - -
0 - -
50 -
004 005 006
- - 10
- - 10
- 1025.0 -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
Remarks
- - Inverter running at a lower speed inhibited
0 1 =7: Quadratic V/f
=0: Linear V/f
=1: V/f with FCC
- - Reverse rotation inhibited
- - Search for the speed of the running motor
with a heavy inertia load so that the motor
runs up to the setpoint
- - Restart after mains blackout
10 5 Ramp-up time from zero to maximum fre-
quency
10 5 Ramp-down time from maximum frequency
to zero
30 30 Boost only effective when accelerating for
the first time (standstill)
0 - Boost only effective when accelerating or
braking
50 - Additional boost over the complete fre-
quency range
007 008 009 010
- - - -
- - - -
- - - -
- - - 8
- - - 1
- - - 2
- - - 127
- - - 500
- - - -
- - - -
- - - 1
- - - -
- - - -
- 1 1 -
- - 1 -
- - 722.1 -
- - 722.2 -
- - 722.3 -
- 755.0 2224 -
- 755.1 755.1 -
011
-
-
-
6
-
-
-
100
1
1000
2
2
1
-
-
-
-
-
-
-
21