Siemens SINAMICS V20 Compact Operating Instructions page 27

Parameter Description
P1005[0...2] Fixed frequency 5 - 14 [Hz]
-
P1014[0...2]
P1015[0...2] Fixed frequency 15 [Hz]
P1016[0...2] Fixed frequency mode
1 Direct selection
2 Binary selection
P1031[0...2] MOP mode
P1032 Inhibit reverse direction of MOP
0 Reverse direction is allowed
1 Reverse direction inhibited
P1040[0...2] Setpoint of the MOP [Hz]
P1047[0...2] MOP ramp-up time of the RFG [s]
P1048[0...2] MOP ramp-down time of the RFG [s]
r1050 CO: Actual output freq. of the MOP [Hz]
P1058[0...2] JOG frequency [Hz]
P1059[0...2] JOG frequency left [Hz]
P1060[0...2] JOG ramp-up time [s]
P1061[0...2] JOG ramp-down time [s]
P1080[0...2] Minimum frequency [Hz]
P1082[0...2] Maximum frequency [Hz]
P1120[0...2] Ramp-up time [s]
P1121[0...2] Ramp-down time [s]
P1130[0...2] Ramp-up initial rounding time [s]
P1131[0...2] Ramp-up final rounding time [s]
P1132[0...2] Ramp-down initial rounding time [s]
P1133[0...2] Ramp-down final rounding time [s]
P1134[0...2] Rounding type
0 Continuous smoothing
1 Discontinuous smoothing
P1135[0...2] OFF3 ramp-down time [s]
P1200 Flying start
0 Flying start disabled
1 Flying start always active; searches in both directions
2 Flying start active after power on, fault, OFF2; searches in both directions
3 Flying start active after fault, OFF2; searches in both directions
4 Flying start always active; searches in direction of setpoint only
5 Flying start active after power on, fault, OFF2; searches in direction of setpoint only
6 Flying start active after fault, OFF2; searches in direction of setpoint only
P1202[0...2] Search rate: flying start [%]
P1203[0...2] Search rate: flying start [%]
r1204 Status word: flying start V/f
Bit Signal
00 Voltage reduced
02 Voltage reduced
04 Current less threshold
07 Speed could not be found
P1210 Automatic restart
0 Disabled
SINAMICS V20 Inverter
A5E37281078-003, 05/2016
Range Factory default
-550.00 - 550.00 0.00
-550.00 - 550.00 0.00
1 - 2 1
0 - 3 1
0 - 1 1
-550.00 - 550.00 5.00
0.00 - 1000.00 10.00
0.00 - 1000.0 10.00
- -
0.00 - 550.00 5.00
0.00 - 550.00 5.00
0.00 - 650.00 10.00
0.00 - 650.00 10.00
0.00 - 550.00 0.00
0.00 - 550.00 50.00
0.00 - 650.00 10.00
0.00 - 650.00 10.00
0.00 - 40.00 0.00
0.00 - 40.00 0.00
0.00 - 40.00 0.00
0.00 - 40.00 0.00
0 - 1 0
0.00 - 650.00 5.00
0 - 6 0
10 - 200 100
10 - 500 100
- -
1 signal Bit
Yes 01
Yes 03
Yes 05
Yes
0 - 8 1
Acc.
level
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
2
2
2
2
2
2
2
3
3
4
Signal name 1
signal
Current could not Yes
be applied
Slope-filter started Yes
Current-minimum Yes
2
27