APV36M0✴❋Series Air Conditioner user & installation manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register E DB98-34573A(1) Mirage_AP36M0@_IBIM_E_34573A(1).indd 57...
Page 2
Features of your new air conditioner Environment-friendly air conditioner Your environment-friendly air conditioner has achieved not only high efficiency, low noise, and energy saving technology but also certified RoHS technology. Energy saving technology with S-inverter system The S-inverter system that changes the capacity of the air conditioner from 10% to 160% with one compressor depending on the usage condition will provide optimal cooling performance with less energy consumption by reducing unnecessary electric consumption.
User manual Safety precautions These warning signs are here to prevent injury to you and others. Please follow them carefully. Important safety symbols and precautions : WARNING Hazards or unsafe practices that may result in severe personal injury or death . CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage .
Page 5
FOR INSTALLATION CAUTION This appliance should be positioned in such a way that it is accessible to the power plug . f Failing to do so may result in electric shock or fire due to electric leakage. Install your appliance on a level and hard floor that can support its weight f Failing to do so may result in abnormal vibrations, noise, or problems with the product.
Page 6
Safety precautions Do not touch the power plug or the circuit breaker with wet hands . f This may result in electric shock. Do not strike or pull the air conditioner with excessive force . f This may result in fire, injury, or problems with the product. Do not place an object near the outdoor unit that allows children to climb onto the machine .
Page 7
Do not drink the water from the air conditioner . f The water may be harmful to humans. Do not apply a strong impact to the remote controller and do not disassemble the remote controller . Do not touch the pipes connected with the product . f This may result in burns or injury.
Checking before use Using indoor unit Make sure that curtain does not block the air inlet . f It may decrease cooling performance by blocking air circulation. In Cool mode, set the appropriate desired temperature . f If the desired temperature is too low, it may be harmful for human body and power consumption will also increase. Set the desired temperature about 5°C lower than the outdoor temperature.
Checking auxiliary power switch Turn on the auxiliary power switch which is installed separately . 1phase circuit breaker 3phase 4wire circuit breaker Auxiliary power switch(NFB, ELB) • Auxiliary power switch is not included in the package. Purchase and install it separately. NOTE •...
Viewing your air conditioner Congratulations on the purchase of the air conditioner. We hope you enjoy the features of your air conditioner and stay cool with optimal efficiency. Please read the manual to get started and to make the best use of the air conditioner. Checking the indoor unit and display Carefully unpack your air conditioner and check the indoor unit to make sure it is not damaged.
Control panel You can operate the air conditioner with the control panel when you can’t or don’t want to operate the air conditioner with the remote controller. (see pages 26~27) Fan speed indicator Air swing (Up/Down) indicator Temperature setting Air swing (Left/Right) indicator Operation mode indicators Timer indicator Mode selection button...
Viewing your air conditioner Checking the remote controller You can activate the air conditioner by pointing the remote controller away from it. When using the remote controller, always point it directly at the air conditioner. Remote controller display Power Turn on/off the air conditioner Mode Set one of the 4 operation modes (see pages 14~17 for instructions)
Page 13
Remote controller display Operation mode indicator Set temperature/time Low battery indicator indicator On/Off timer indicator Transmit indicator Fan speed indicator Auto Air swing indicator Medium High Using the remote controller Point the remote controller towards the remote controller receiver of the indoor unit (see page 11 to find the location of remote controller receiver).
Operating basic function Turning the air conditioner on and off Press the Power button on the remote controller. You will hear a ring and the air flow blade will move automatically when the air conditioner is properly on. The air conditioner will operate in the most recent operation mode used or Auto mode.
Page 15
Cool In Cool mode, the air conditioner will cool your room. You can adjust the temperature and the fan speed to feel cooler in hot season. 1. Turn on the air conditioner. Press the Power button on the remote controller. 2.
Page 16
Operating basic function The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air. Dry mode makes the air feel refreshing in a humid climate. 1. Turn on the air conditioner. Press the Power button on the remote controller.
Page 17
Fan mode can be selected to ventilate your room. Fan mode will be helpful to refresh the stale air in your room. 1. Turn on the air conditioner. Press the Power button on the remote controller. 2. Set the operation mode. Press the Mode button on the remote controller until Fan mode indicator appears on the remote controller display.
Using advanced functions Using the Purity function Purifying operation will get rid of the active oxygen and provide fresh air. 1. Press the Purity button on the remote controller while the air conditioner is on or off. When the air conditioner is off Purity function will be turned on.
Using the Turbo function Turbo function will be helpful to cool or heat your room quickly and effectively by operating at the maximum fan speed for 30 minutes. 1. Turn on the air conditioner. Press the Power button on the remote controller. 2.
Using advanced functions Using the Long function Long function will be helpful when you want the cool or warm air to go to much further place. 1. Turn on the air conditioner. Press the Power button on the remote controller. 2.
Adjusting the air flow direction Air flow can be directed to your desired position. Vertical air flow 1. Press the Air swing(Up/Down) button on the remote controller. The air flow blades move up and down. To keep the air flow direction in a constant position, press the Air swing(Up/Down) button on the remote controller again.
Page 22
Using advanced functions Horizontal air flow 1. Press the Air swing(Left/Right) button on the remote controller. The air flow blades move right and left. To keep the air flow direction in a constant position, press the Air swing(Left/Right) button on the remote controller again.
Setting timer This advanced Timer function allows you to turn on/off your air conditioner automatically even when you are away. Simply set the time and your air conditioner will turn on/off automatically. On Timer This function allows you to turn on the air conditioner automatically within the time range of 24 hours.
Page 24
Using advanced functions Off Timer This function allows you to turn off the air conditioner automatically within the time range of 24 hours. Off timer is available while your air conditioner is on. 1. Press the Off Timer button on the remote controller. Off timer indicator blinks on the remote controller display.
Page 25
Combining On Timer and Off Timer You can combine the On timer and Off timer together for more convenient use of the timer function. 1. Set the On timer. Press the On Timer button. Set the time with Time Up or Time Down button. Press Set button to activate the On timer.
Using advanced functions Using the air conditioner with the control panel You can control the air conditioner without the remote controller. 1. Press the Power button on the indoor unit control panel. You will hear a ringing sound and the air conditioner will operate in the most recent operation mode used or Auto mode. To turn off the air conditioner, press the Power button again.
5. Press Air swing (Up/Down) or Air swing (Left/Right) button to adjust air flow direction. The air flow blades move up/down or left/right. To keep the air flow direction in a constant position, press the Air swing (Up/Down) or Air swing (Left/Right) button on the control panel again.
Cleaning and maintaining the air conditioner Make sure to turn off the circuit breaker when cleaning the air conditioner. CAUTION Cleaning the exterior 1. Wipe the surface of the unit with a slightly wet or dry cloth when needed. Do not use Benzene, Thinner or Clorox .
Maintaining your air conditioner If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it in best condition. 1. Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and turn off the circuit breaker. There may be internal damage if moisture is left in components.
Page 30
Cleaning and maintaining the air conditioner Internal protections via the unit control system This internal protection operates if an internal fault occurs in the air conditioner. Type Description The air conditioner does not start operating immediately to protect the compressor of the Protect compressor outdoor unit after it has been started.
Appendix Troubleshooting Refer to the following chart if the air conditioner operates abnormally. This may save time and unnecessary expenses. PROBLEM SOLUTION • Check power status and then operate the air conditioner again. The air conditioner does not • Check whether the power plug is connected correctly or the auxiliary power switch is work at all .
Page 32
Appendix PROBLEM SOLUTION Timer function is not working . • Check if you have pressed the Set button on the remote controller after setting the time. • Odor may permeate depending on the surrounding environment or operating condition. Ventilate the indoor air or operate Fan mode for 1~2 hours if the odor does not go away. Odors permeate in the room (Part of the air conditioner does not generate any odor) during operation.
This manual explains how to install an indoor unit with a split system with two SAMSUNG units. The use of other types of units with different control systems may damage the units and invalidate the warranty. The manufacturer shall not be responsible for damages arising from the use of non compliant units.
Page 34
Safety precautions f Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires, explosions or injuries. f Our units must be installed in compliance with the spaces indicated in the manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs.
Installing the air conditioner Contact service center for installation. This air conditioner can only be installed by the qualified installer with the certification issued by Samsung electronics. Caution for installation f Make sure that the air inlet and outlet of the air conditioner is not partially or entirely blocked by surrounding object.
Installing the air conditioner f If you need to ensure the outdoor unit from falling, use wires to fix it firmly. - Loosen the 4 screws from the top cover of the outdoor unit. - Put the wire around the screws and fasten the screws. - Fix the wire on the ground.
Page 37
4. Refrigerant piping work 1) Cut the pipe with a pipe cutter ensuring that the cut edge remains flat and then remove all the burrs. 2) Make sure that the flared pipe doesn’t have uneven thickness, damaged and cracked surfaces, or any other defects. 3) You must use torque wrench when connecting pipes or flare nut.
Page 38
Outdoor unit Amount of additional refrigerant Model name (for every 1m) side APV36M0* Series Liquid side 2) After charging the refrigerant, disconnect the manifold gauge from service port and tighten the cap nut. (Preventing leakage) 9. Installing an oil trap Check the following list and install an oil trap.
Page 39
10. Insulating the refrigerant pipes - Make sure to insulated the refrigerant pipes with an insulation tape. If the Pipe insulator pipe is not insulated, condensate may form and drop into the indoor. Vinyl tape - Wind the refrigerant pipes and the drain hose with vinyl tapes. Indoor/Outdoor - When you bend the pipe, try to secure large bending radius (over 100mm) unit connection...
Page 40
Installing the air conditioner 12. Connecting drain hose 1) To prevent condensation from forming on the drain hose, insulated the drain hose with a supplied insulator. 2) Connect the drain hose by pushing the extension drain hose to the insulated drain pipe. 3) Tightly insulated the connection part of the extension drain hose to the insulated drain hose and fix them with a cable tie or tape.
Pump down procedure (When removing the product) 1. Select Cool mode after turning on the air conditioner and run the compressor for 3 minutes. 2. Release the valve caps on high and low pressure side. 3. Use L wrench to close the valve on the high pressure side. 4.
Page 42
Installing the air conditioner Power specification f Wiring standards Item APV36M0✴ Series Indoor unit APV36M0AN Model name Outdoor unit APV36M0AX Power Product Single phase 230V, 60Hz Capacity of circuit breaker Product Thickness of ground wire Indoor and outdoor unit power wire 0.75...
Page 43
Connecting the power terminal f Connect the cables to the terminal board with solderless ring terminals. f Only sue the certified and rated cables and make sure to firmly connect them without applying any external force to the terminal. f Connect with a driver and a wrench that are able to apply the rated torque to the screws. f Connect the terminal screws according to the rated tightening torque.
Page 44
Installing the air conditioner Order of electrical connection f Entire system diagram Power supply cable Communication cable Distributing board Communication cable Outdoor unit Single phase 220V/60Hz Indoor/Outdoor unit Indoor Ground wire Ground wire connection cable unit f Indoor and outdoor unit connection diagram Outdoor Unit Indoor unit 1(L) 2(N)
Page 45
Echo mode: Displays energy saving mode or standby mode Displays echo mode 7-segment display Key Switch ❋ ❋ Echo mode is displayed in lamp Model series APV36M0✴ Series Display Echo mode lamp Mode Segment 1 Segment 2 Segment 3...
Page 47
Number of short Contents on the screen SEG1 SEG2 SEG3 SEG4 Unit press Protection control Frequency status 0: No protection control 0: Normal 1: Frozen 0: Cooling 1: Hold Protection control 2: Non-stop defrost 1: Heating 2: Down 3: Overload 3: Up_limit 4: Discharge 4: Down_limit...
Page 48
- [K3] button – Reset the outdoor unit power and cancel the echo mode (standby mode) Located in Main PCB 7-segment display Key Switch f Single phase : APV36M0* Series 5. DIP switch option On (Default) Switch 1 Auto address setting...
Page 50
Installing the air conditioner Failure diagnosis f When error occurs during operation, error mode will appear on the outdoor unit MAIN PCB display. LED Display No . PCB type Description/Remarks/7 Segment display Green Yellow Normal operation (MAIN: Indoor unit 扌 Outdoor unit: Green turns on) Description (INVERTER: Main PCB 扌...
Page 51
LED Display No . PCB type Description/Remarks/7 Segment display Green Yellow Outdoor unit overload protection control (When Description compressor stops) MAIN Remarks Check when the compressor operates again 7 SEG. E404 Outdoor unit compressor discharge temperature Description protection control ...
Page 52
Installing the air conditioner LED Display No . PCB type Description/Remarks/7 Segment display Green Yellow Description Compressor rotation error MAIN / Remarks Check the connection of the compressor INVERTER 7 SEG. E467 Description Current sensor error MAIN / ...
How to connect your extended power cables ❋ ❋ Items to prepare (compressor and insulation tape should be prepared by an installation technician.) Tools Crimping plier Connection sleeve (mm) Insulation tape Contraction tube (mm) Spec MH-14 20 x ø 6.5(HxOD) Width 19mm 70 x ø...
Page 54
How to connect your extended power cables 5. Apply heat to the service tube to contract it. Service tube 6. After tube contraction work is completed, wrap it with the insulation tape Insulation tape to finish. • In case of extending the electric wire, please DO NOT use a round-shaped pressing socket. - Incomplete wire connections can cause electric shock or a fire.
Installing the interface module Installation procedure and method 1. Remove the cover of the electrical component box. - Remove the cabinet on the side of the outdoor unt. 2. Attach the interface module - Refer to the illustration for the location and attach the interface module. When you attach the interface module, make sure that it doesn’t get tangled with the wires or other parts.
Page 56
QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT 1-800-10-SAMSUNG(726-7864) for PLDT 1-800-3-SAMSUNG(726-7864) for Digitel PHILIPPINES www.samsung.com 1-800-8-SAMSUNG(726-7864) for Globe 02-5805777 Mirage_AP36M0@_IBIM_E_34573A(1).indd 56 2012-02-21 오후 1:10:05...