Error Information Page - Panasonic PT-D10000E Operating Instructions Manual

How to use network function (continued)
■

Error information page

When
details.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.
●
When [FAILED] has appeared for an item
MAIN CPU BUS MAIN CPU BUS
FAN FAN
OPTICS MODULE TEMPERATURE OPTICS MODULE TEMPERATURE
INPUT AIR TEMPERATURE INPUT AIR TEMPERATURE
OUTPUT AIR TEMPERATURE OUTPUT AIR TEMPERATURE
LAMP REMAIN TIME LAMP REMAIN TIME
LAMP STATUS LAMP STATUS
APERTURE APERTURE
(CONTRAST-SHUTTER) (CONTRAST-SHUTTER)
SHUTTER SHUTTER
(MUTE-SHUTTER (MUTE-SHUTTER
DIRTY AIR FILTER DIRTY AIR FILTER
AIR FILTER CLEANER UNIT AIR FILTER CLEANER UNIT
OPTICS MODULE TEMP.SENSOR OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR INPUT AIR TEMP.SENSOR
OUTPUT TEMP. SENSOR OUTPUT TEMP. SENSOR
BATTERY BATTERY
AIRFLOW SENSOR AIRFLOW SENSOR
AC POWER AC POWER
LENS SHIFT LENS SHIFT
90
– ENGLISH
Parameter Parameter
is displayed on the status information screen, click it to display the error
Trouble has occurred in the microcomputer circuitry. Consult your dealer. Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer. Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. It may be that the projector is being The temperature inside the projector is high. It may be that the projector is being
used where the ambient temperature is high such as near a heating appliance. used where the ambient temperature is high such as near a heating appliance.
The input air temperature is too high. It may be that the projector is being used The input air temperature is too high. It may be that the projector is being used
where the ambient temperature is high such as near a heating appliance. where the ambient temperature is high such as near a heating appliance.
The temperature around the lamp is too high. It may be that the projector's The temperature around the lamp is too high. It may be that the projector's
ventilation holes are blocked. ventilation holes are blocked.
The lamp runtime has exceeded the prescribed cumulative time, and it is now The lamp runtime has exceeded the prescribed cumulative time, and it is now
time to replace the lamp. time to replace the lamp.
The lamp has failed to light. The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power. Wait a short while for the lamp to cool off, and then turn on the power.
Trouble has occurred in the contrast shutter circuitry. Consult your dealer. Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
Trouble has occurred in the shutter circuitry. Consult your dealer. Trouble has occurred in the shutter circuitry. Consult your dealer.
The air filter is blocked with dust. The air filter is blocked with dust.
Turn off the MAIN POWER switch by following the procedure on page 36, and Turn off the MAIN POWER switch by following the procedure on page 36, and
then clean the air filter. (pp. 108, 109) then clean the air filter. (pp. 108, 109)
The air filter unit is not installed. Install the air filter unit. The air filter unit is not installed. Install the air filter unit.
Trouble has occurred in the temperature detection sensor inside the projector. Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer. Consult your dealer.
Trouble has occurred in the sensor used to detect the input air temperature. Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer. Consult your dealer.
Trouble has occurred in the sensor used to detect the exhaust air temperature. Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer. Consult your dealer.
The backup battery has been run out. Consult your dealer. The backup battery has been run out. Consult your dealer.
Problem with air flow sensor. Consult your dealer. Problem with air flow sensor. Consult your dealer.
AC power supply voltage input has dropped. Check that there is sufficient AC power supply voltage input has dropped. Check that there is sufficient
electrical wiring capacity for the projector's power consumption requirements. electrical wiring capacity for the projector's power consumption requirements.
Problem with lens shift circuit. Consult your dealer. Problem with lens shift circuit. Consult your dealer.
OK: Normal operation OK: Normal operation
FAILED: Occurrence of trouble FAILED: Occurrence of trouble
Description Description