Common Features - Icom IC-F4062S Sales Handbook

IP55 Dust-protection and splash, water jet resistance
The IC-F3062 series meets IP55 requirements for dust-
protection, splash and water jet resistance. Its durable
construction is backed up by the aluminum diecast
chassis and polycarbonate casing, allowing reliable
operation under harsh weather and environmental
conditions.
A simple explanation of the IP rating system is written
below. Please refer to more specialized information
material if you wish to know more.
An IP number contains two numbers (i.e. IP65) in most
instances which relate to the level of protection provided
by an enclosure or housing. Either number may be
shown as "X" (i.e. IPX6 / IP7X) to indicate the "X" part is
not tested.
The first number relates to protection from solids as
follows:
0: No special protection
1: Protected against solid objects up to 50 mm in
diameter
2: Protected against solid objects up to 12 mm in
diameter
3: Protected against solid objects up to 2.5 mm in
diameter
4: Protected against solid objects up to 1 mm in
diameter
5: Dust protected
6: Dust tight
The second number relates to protection from liquids as
follows:
0: No special protection
1: Protected against vertically falling drops of water
2: Protected against direct sprays up to 15
vertical
3: Protected against direct sprays up to 60
vertical
4: Protected against sprays from all directions (limited
ingress permitted)‫‏‬
5: Protected against low pressure jets of water from all
directions (limited ingress permitted)‫‏‬
6: Protected against strong jets of water e.g. for use on
ship decks (limited ingress permitted)‫‏‬
7: Protected against the effects of temporary immersion
between 15cm and 1m for 30min.
8: Protected against long periods of immersion under
pressure
(Water-level and submersion time set by
manufacturer)‫‏‬

Common Features

Enhanced audio
The IC-F3062 series employs a BTL (Bridged-Tied Loads
) amplifier that increases the audio output and the built-
in audio compander provides clear, low noise
communications.
The aluminum die-cast chassis and polycarbonate
casing combination have been tested to MIL standard
specifications.
The MIL-STD-810 series of standards are issued by the
United States Army's Developmental Test Command, to
specify various environmental tests to prove that
equipment qualified to the standard will survive in the
field
Icom makes rugged products
that have been tested to and
passed the following MIL-STD
requirements and strict
environmental standards.
Low Pressure
High Temp.
Low Temp.
o
from the
Temp. Shock
Solar Radiation
Rain Blowing/Drip
o from the Humidity
Salt Fog
Dust Blowing
Vibration
Shock
MIL 810C MIL 810D
Standard
Method Proc. Method
500.1 I 500.2
501.1 I 501.2
502.1 I 502.2
503.1 I 503.2
505.1 I 505.2
506.1 I, II 506.2
507.1 I, II 507.2
509.1 I 509.2
510.1 I 510.2
514.2 VIII, X 514.3
516.2 I, II, V 516.3
MIL 810E MIL 810F
Proc. Method Proc. Method Proc.
I, II 500.3 I, II 500.4
I, II 501.3 I, II 501.4
I, II 502.3 I, II 502.4-3
I 503.3 I 503.4
I 505.3 I 505.4
I, II 506.3 I, II 506.4 I, III
II, III 507.3 II, III 507.4
I 509.3 I 509.4
I 510.3 I 510.4
I 514.4 I 514.5
I, IV 516.4 I, IV 516.5 I, IV
I, II
I, II
I, II
I
I
–
–
I
I
7