Icom IC-F4062S Sales Handbook page 23

HIGH/LOW KEY "H/L"
Push to select the transmit output power temporarily or
permanently, depending on the pre-setting.
• Ask your dealer for the output power level for each
selection.
C.TONE CH ENT KEY "TSEL"
Push to select the continuous tone channel using
[CH Up]/[CH Down] to change the tone frequency/code
setting. The selected channel remains set as the
continuous tone channel until another channel is
designated as such.
TALK AROUND KEY "TA"
Push to turn the talk around function ON and OFF.
• The talk around function equalizes the transmit
frequency to the receive frequency for transceiver-to-
transceiver communication.
WIDE/NARROW KEY "W/N"
Push to toggle the IF bandwidth between wide and
narrow.
•The wide passband width can be selected from 25.0 or
20.0 kHz using the CS-F3060 CLONING SOFTWARE.
(PMR or BIIS PMR operation only) Ask your Dealer for
details.
DTMF AUTODIAL KEY "DTMA"
➥Push to enter the DTMF channel selection mode. Then
select the desired DTMF channel using [CH Up]/[CH
Down].
➥After selecting the desired DTMF channel, push this
key to transmit the DTMF code.
RE-DIAL KEY "DTMR"
Push to transmit the last-transmitted DTMF code.
CALL KEYS "CALL" "CALA" "CALB"
Push to transmit a 2-tone
•Call transmission is necessary before you call another
station depending on your signaling system.
• [Call A] and/or [Call B] may be available when your
system employs selective 'Individual/Group' calls. Ask
your dealer which call is assigned to each key.
EMERGENCY KEY "EMR"
➥ Push and hold for a specified period to transmit an
emergency call.
➥When [Emergency Single (Silent)] or [Emergency
Repeat (Silent)] is pushed, an emergency call is
transmitted without a beep emission and LCD indication
change.*
• If you want to cancel the emergency call, push (or
push and hold) the key again before transmitting the
call.
Functions Programmable to Keys
(a 2/5-tone/BIIS ID code).
• The emergency call is transmitted one time only or
repeatedly until receiving a control code depending
on the pre-setting.
*BIIS PMR operation only
SURVEILLANCE KEY "SURV"
Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not
emitted and the LCD backlight does not light when
a signal is received or a key is pushed, etc.
TX CODE ENTER KEY "TXCE"
(PMR or BIIS PMR operation only)‫‏‬
Push to enter the ID code edit mode directly, for both
5-tone and BIIS. Then set the desired digit using
[CH Up]/
[CH Down] or 10-keypad*.
*IC-F3062T/IC-F3063T/IC-F4062T /IC-F4063T (10-
key type) only
TX CODE CHANNEL SELECT KEY "TXC"
➥Push to enter the ID code channel selection mode
directly. Then set the desired channel using [CH
Up]/[CH Down].
➥During ID code channel selection mode, push for 1
sec. to enter the ID code edit mode for 5-tone and
BIIS. Then set the desired digit using [CH Up]/[CH
Down] or 10-keypad*.
*IC-F3062T/IC-F3063T/IC-F4062T /IC-F4063T (10-
key type) only
TX CODE CHANNEL UP/DOWN KEYS "TXCU" "TXCD"
Push to select a TX code channel directly.
ID-MR SELECT KEY "IDMS"
(PMR or BIIS PMR operation only)‫‏‬
➥Recalls detected ID codes.
• Push this key, then select the ID code using [CH
Up]/[CH Down].
• Up to 5 ID's are memorized.
➥Push and hold to erase the selected ID's.
SCRAMBLER FUNCTION "SCR"
Push to toggle the voice scrambler function ON and
OFF.
COMPANDER KEY "COMP"
Push to toggle the compander function ON and OFF.
The compander function reduces noise components
from the transmitting audio to provide clear
communication.
PHONE KEY "PHN"
Push to connect or disconnect the telephone
network connection during LTR operation.
23