Rear Section - JVC gy-dv5100 Instructions Manual

2-5 Rear Section

t
y
u
DC OUT
r
1 [TALLY] Tally lamp
This lamp lights up when the GY-DV5100 enters the record
mode. It blinks during the transition to the record mode.
● Use the BACK TALLY item on the OTHERS (2/2) menu
screen to select whether or not the lamp should light and
the lighting pattern.
☞ See "BACK TALLY" on page 87.
2 [CH-1/CH-2 REAR AUDIO IN] CH-1/CH-2 Audio
input connector on the rear section
Connect external audio equipment or a microphone to this
connector.
● Set the CH-1/CH-2 REAR AUDIO IN switch B on page
16 in accordance with the connected equipment.
● To record the audio signal input through this connector,
set the CH-1 or CH-2 AUDIO IN switch 0 on page 16 to
"REAR". The audio from this connector is recorded on
the channel set to "REAR".
2 1
3
3 [DC IN] DC input connector (XLR 4-pin)
Power input connector for 12 V DC. Connect to the optional
AA-P250 power adapter. When a cable is connected here,
the power supply from the battery pack is interrupted and
the source is switched to the power supplied through this
connector.
1
2
Downloaded From CamcorderManual.com JVC Manuals
PHONES TALLY
DV INT
DC IN
CH-1 CH-2
REAR AUDIO IN
e w
No. Signal
1 GND
2 HOT
3 COLD
No.
1
GND
2
—
4
3
—
3
4
+12V
2. CONTROLS, INDICATORS AND CONNECTORS
4 [DC OUT] DC output connector
Connector for power output to a wireless microphone
transmitter, etc. The supply voltage is identical to the voltage
supplied to the unit (DC 17 V max. 0.3 A).
4
3
(Surface profile)
q
5 [PHONES] Earphone jack
This is a stereo mini-jack for connecting an earphone for
audio monitoring. Plug in an earphone or headphone with
a 3.5 mm diameter plug. The earphone can also be used to
monitor alarm tones in accordance with the circumstances.
The sound from the monitoring speaker is interrupted when
an earphone is connected here.
The audio channel to be output is selected with the AUDIO
SELECT item on the AUDIO/VIDEO menu screen and
MONITOR SELECT switch C on page 16.
The audio output level is adjusted with the Audio monitor
volume control 1 on page 12.
MEMO:
● The volume of the alarm sound is set with the ALARM
VR LEVEL item on the OTHERS (2/2) menu screen.
● When using a stereotype jack and stereo sound
should be output, the following setting should be
performed.
Set the MONITOR SELECT switch to "MIX".
Set the AUDIO MONITOR item on the AUDIO/VIDEO
menu screen to STEREO.
6 [DV/INT]DV/INT selector switch
This switch is used to select whether to connect the optional
DV Disk Recorder to this camera or a digital video
component to the 7 DV connector.
DV: Connect a digital video component to the DV
connector
INT: Connect a DV Disk Recorder to the camera
* Turn the camera off before using this switch.
7 [DV] connector
Using a DV cable (optional), a digital video component with
DV connector can be connected here.
This connector is used for input and output of the DV signal
or to input the VTR control signal from a digital video
component with DV connector.
To record the DV signal from this connector, set the unit to
the VTR mode. (Press the MODE switch F on page 14
upward to turn on the VTR indicator.)
● Camera mode:
The DV compressed signal (IEEE1394) of the camera
image is output.
● VTR mode:
Signal The DV input signal from this connector can be recorded
on tape. During playback, the tape playback DV
compressed signal is output.
MEMO:
To receive FF/REW remote control signals from this
connector, select the setting with the REM FF/REW
MODE item on the OTHERS (1/2) menu screen.
1
No. Signal
1
GND
2
—
3 —
4
DC 12V (power through)
2
19