Time Code Presetting Procedure - JVC gy-dv5100 Instructions Manual

TIME CODE PRESETTING PROCEDURE

SHUTTER dial
CAMERA OPERATION..
CAMERA PROCESS..
AUDIO/VIDEO..
LCD/VF..
TC/UB/CLOCK..
OTHERS..
FILE MANAGE..
MENU ALL RESET
EXIT
TC/UB/CLOCK menu screen
––– TC/UB/CLOCK –––
TC PRESET
UB PRESET
DROP/NON DROP DROP
HEADER REC..
TIME/DATE..
PAGE BACK
Time code (hour, min, sec, frame)
PRESETTING USER'S BIT DATA
––– TC/UB/CLOCK –––
TC PRESET
UB PRESET
DROP/NON DROP DROP
HEADER REC..
TIME/DATE..
PAGE BACK
Align the cursor with UB
Zero-resetting the Time Code or User's Bit Data
This is performed with the TC or UB PRESET item on the TC/UB/CLOCK menu screen. (Performed separately for the time
code and the user's bit data.)
1 Rotate the SHUTTER dial to align the cursor ( ) with the TC or UB PRESET item, and then press the SHUTTER dial.
2 Rotate the SHUTTER dial to select ZERO PRESET as the setting value, and then press the SHUTTER dial.
Downloaded From CamcorderManual.com JVC Manuals
EDITSEARCH
MONITOR
FILTER
1 3200K
5600K 1 8 / ND
2
.3 5600K
.4 5600K 1 64 / ND
STATUS
SHUTTER
LCD BRIGHT
MENU
AUDIO
LEVEL
FRONT
REAR
AUTO IRIS FULL AUTO BLACK LOLUX
CH-1 CH-2
CH-1
MODE AUDIO IN
BACK L STRETCH
VTR AUDIO SELECT
NORMAL NORMAL CH-1
SPOT L COMPRESS AUTO
CAM
MANUAL
POWER VTR
ON OFF
STATUS button
TOP MENU screen
––– MENU –––
CANCEL
00:00:00:00
EXECUTE
00 00 00 00
EXECUTE
00:00:00:00
EXECUTE
00 00 00 00
EXECUTE
The time code and user's bit data are preset on the TC/UB/
CLOCK menu screen.
1.
Display the TC/UB/CLOCK menu screen.
1 Press the Status button for 1 second or more to display
OPEN
the TOP MENU screen.
2 Rotate the SHUTTER dial to align the cursor ( ) with
DISPLAY
PULL the TC/UB/CLOCK item, and then press the SHUTTER
OPEN
CH-2
CH-2
dial.
● The TC/UB/CLOCK menu screen appears.
2.
Set the time code (hours, minutes, seconds, frames).
1 Rotate the SHUTTER dial to align the cursor ( ) with TC
PRESET, and then press the SHUTTER dial.
● The first digit of the time code blinks.
The blinking digit is the one to be set.
2 When the SHUTTER dial is pressed, the blinking digit
changes.
3 When the SHUTTER dial is rotated, the value of the
blinking digit changes.
When the SHUTTER dial is rotated upward, the value
becomes higher. When rotated downward, the value
becomes smaller.
4 Repeat the procedure described in 2 and 3 above to
set the desired value for all digits.
5 After setting the frame digit, press the SHUTTER dial to
make EXECUTE blink. The setting values are confirmed
when the SHUTTER dial is pressed again.
To cancel the setting, select CANCEL and press the
SHUTTER dial.
3.
When all the digits are set.
● Press the STATUS button to return to the normal screen
or
● Rotate the SHUTTER dial to align the cursor ( ) with the
PAGE BACK item, and then press the SHUTTER dial to
return to the TOP MENU screen.
The user's bit data are preset with the UB PRESET item on the
TC/UB/CLOCK menu screen.
The method for setting is the same as the method for setting
the time code described above.
● The user's bit can be specified using numerals or alphabetic
letters from 0 to F for each digit.
CAUTION:
It is not possible to set all the digits of the user's bit data to
"F". Reading of the data during playback will not be possible
for an all-F setting.
10. TIME CODE OPERATION
69