Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual page 134

RS-232C interface
5.Command table
_Commands relating to operation control
<Notes>
As the return (completion) message, [ACK] is returned
when data is received, and only the execution message
which is subsequently returned is listed in the table.
If a command not listed in the table is received, ER001
(invalid command) is returned after [ACK].
VTR
Send command
operation
STOP
[STX] OSP [ETX]
This command is for stopping the tape transport. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
For details, refer to the setup menus.
EJECT
[STX] OEJ [ETX]
This command is for ejecting the cassette tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
For details, refer to the setup menus.
PLAY
[STX] OPL [ETX]
This command is for starting playback.
REWIND
[STX] ORW [ETX] ←→
This command is for rewinding the tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
The maximum speed differs according to the setting
selected for the setup menu item No.102 (FF. REW
MAX).
For details, refer to the setup menus.
FAST
[STX] OFF [ETX]
FORWARD
This command is for fast forwarding the tape. The
resulting output picture and sound statuses differ
according to the setting selected for the setup menu
item No.105 (AUTO EE SEL).
The maximum speed differs according to the setting
selected for the setup menu item No.102 (FF. REW
MAX).
For details, refer to the setup menus.
REC
[STX] ORC [ETX]
This command is for starting recording.
134
(continued)
Return (completion)
message
←→
[STX] OSP [ETX]
←→ [STX] OEJ [ETX]
←→
[STX] OPL [ETX]
[STX] ORW [ETX]
←→ [STX] OFF [ETX]
←→ [STX] ORC [ETX]
VTR
Send command
operation
SHTL
[STX] OSF:data [ETX]←→ [STX] OSF [ETX]
FORWARD
This is the forward direction shuttle command.
data = n:speed data
0:STILL
1:k0.03
2:k0.1
3:k0.2
4:k0.5
5:k1
6:k2.0
(1.85k for formats other than
DVCPROHD-LP)
7:k4.9
8:k9.8
9:k16
A:k32
<Note>
k k
The 16 and 32
setting selected for setup menu item No.101 (SHTL
MAX).
SHTL
[STX] OSR:data [ETX]←→ [STX] OSR [ETX]
REVERSE
This is the reverse direction shuttle command.
data = n:speed data
0:STILL
1:k0.03
2:k0.1
3:k0.2
4:k0.5
5:k1
6:k2.0
(1.85k for formats other than
DVCPROHD-LP)
7:k4.9
8:k9.8
9:k16
A:k32
<Note>
The 16k and 32k speeds differ according to the
setting selected for setup menu item No.101 (SHTL
MAX).
STANDBY
[STX] OBF [ETX]
OFF
This command is for setting the VTR to standby OFF.
STANDBY
[STX] OBN [ETX]
ON
This command is for setting the VTR to standby ON.
Return (completion)
message
speeds differ according to the
←→ [STX] OBF [ETX]
←→
[STX] OBN [ETX]