Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual page 130

Error messages
Error messages (continued)
Description
Display
VTR operation and remedial action
E-51 If the take-up reel has turned without engaging
FRONT LOAD the tape for a specific period of time during the
tape start or end processing operation while
ERROR
loading is being performed (at the half position),
the AUTO OFF lamp lights, and the message
display blinks.
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-52 If, after the cassette has been inserted, the tape
take-up reel has not wound up the tape while the
W-UP REEL
total tape amount is not detected and while the
NOT ROTA
tape is traveling, the AUTO OFF lamp lights, and
the message display blinks.
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-53 If, after the total tape amount has been detected,
the amount of tape wound up onto the take-up
WINDUP
reel and the amount of tape supplied by the
ERROR
supply reel differ to an abnormal extent while the
tape is traveling, the AUTO OFF lamp lights, and
the message display blinks.
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-55 If the tape has not been wound up during
UNLOAD unloading, the AUTO OFF lamp lights, and the
message display blinks.
ERROR
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-57 When the tape start or end processing operation is
not completed, the AUTO OFF lamp lights, and the
S-FF/REW
message display blinks.
TIMEOVER
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-59 If the rotational speed of the cylinder motor is
DRUM ROTA abnormally slow, the AUTO OFF lamp lights, and
the message display blinks.
TOO SLOW
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-60 If the rotational speed of the cylinder motor is
abnormally high, the AUTO OFF lamp lights, and
DRUM ROTA
the message display blinks.
TOO FAST
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-61 If the rotational speed of the cylinder motor is
abnormally slow, the AUTO OFF lamp lights, and
CAP ROTA
the message display blinks.
TOO SLOW
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-64 If the supply reel motor rotates at an abnormally
fast rate, the AUTO OFF lamp lights, and the
S REEL ROTA
message display blinks.
TOO FAST
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-67 If the take-up reel motor rotates at an abnormally
fast rate, the AUTO OFF lamp lights, and the
T REEL ROTA
message display blinks.
TOO FAST
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
130
(continued)
Description
Display
VTR operation and remedial action
E-69 If an abnormal torque applied to the supply reel
motor is detected or if an abnormal current flowing
T REEL
to the current-sensing resistor is detected, the
TORQUE ERR
AUTO OFF lamp lights, and the message display
blinks.
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-70 When the tape start or end processing operation is
not completed, the AUTO OFF lamp lights, and the
S REEL
message display blinks.
TORQUE ERR
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-71 If an abnormal tension is detected at the supply
side in the capstan mode, the AUTO OFF lamp
CAP TENSION
lights, and the message display blinks.
ERROR
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-72 If an abnormal tension at the supply side is
detected in the reel mode, the AUTO OFF lamp
REEL
lights, and the message display blinks.
TENSION
VTR: Stops.
ERROR
Set the POWER switch to OFF and then back to
ON again.
E-73 If the take-up reel motor is running in the reverse
direction, the AUTO OFF lamp lights, and the
REEL DIR
message display blinks.
UNMATCH
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-74 If excess torque being applied to the cylinder motor
DRUM is detected, this error number flashes on the
TORQUE display.
ERROR VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
E-FF If the tape start and tape end are detected at the
same time either during or after loading, the AUTO
OFF lamp lights, and the message display blinks.
VTR: Stops.
Set the POWER switch to OFF and then back to
ON again.
If the error message display persists even after the
VTR has been shut down and started up again,
consult your dealer.