Example Of Connections In 23/24 Hz Or 25/50 Hz (Hd) Mode; Example Of Connections In 25/50 Hz (Sd); Mode - Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual

Connections
(continued)
Example of connections in 23/24 Hz or 25/
50 Hz (HD) mode
When a tape recorded with a frame rate of 24 fps (25/50 fps)
using a variable frame rate camera is played back on the
unit, data can be converted and output in 1080/24 psf (1080/
25 psf or 1080/50i) and recorded on the AJ-HD3700 series.
Shown in the figure below is an example of the deck-to-deck
connections.
Input the 48 Hz (or 50 Hz) reference signal as the REF input.
HD SDI OUT
AJ-HD1800
(Source side)
Reference signal
For 24 Hz mode:
HD REF 48 Hz (Interlace)
For 25 Hz (HD)/50 Hz (HD) mode:
HD REF 50 Hz (Interlace) or
SD REF 50 Hz (Interlace)
75h
termination
AJ-HD3700B
ON
(Recorder side)
REF IN
HD SD
~
AC IN FUSE
125V 5A
ON ON
75g 75g
OFF OFF
SD
HD SD
REF OUT
REMOTE
IN
AUDIO IN
CH 1 CH 2
AUDIO OUT
CH 1 CH 2
PUSH PUSH PUSH
SIGNAL
GND
REMOTE
IN/OUT
<Notes>
When the tape begins to travel at 1k speed, the video
may be disturbed and the audio muted for several frames
in order to synchronize the REF input with the tape.
VITC signals are not output to the SD SDI and VIDEO
OUT connectors in the 23/24 Hz mode.
In the 25/50 (HD) Hz mode, the output video signals of the
SD SDI and VIDEO OUT connectors are delayed by
approximately 1 field in relation to the HD SDI output.
HD SDI output is muted in the 25/50 Hz (SD) mode.
22
REMOTE
75h
IN/OUT
termination
OFF
HD SDI signal
HD SDI IN
Remote
signal (9P)
VIDEO OUT WFM SD SDI HD SDI
1 2 3 IN OUT1 IN OUT OUT
1 3
(SUPER) ACTIVE ACTIVE
THROUGH THROUGH
OUT
CH CH CH CH
INPUT OUT2
2
MONITOR
(SUPER)
SPARE MONITOR
CH CH OUTPUT CH CH
(SUPER)
DIGITAL AUDIO
REMOTE REMOTE V/A RS-232C
OUT IN/OUT CONTROL
PARALLEL
IN/OUT
(50P)
CONTROL
PANEL
TIME CODE
CH 3 CH 4 CH 5 IN PUSH OUT
MONITOR
CH 3 CH 4 CUE L R
PUSH PUSH PUSH PUSH
Video monitor

Example of connections in 25/50 Hz (SD)

mode

When a tape recorded with a frame rate of 25/50 fps using a
variable frame rate camera is played back on the unit, data
can be converted and output in 576/50i and recorded in the
SD-VTR. An example of a connection between decks is
shown in the following illustration.
Input the 50 Hz reference signal to the SD REF input
connector as the REF input.
SD SDI OUT
AJ-HD1800
(Source side)
Reference signal
SD REF 50Hz
(interlace)
AJ-SD965
(Recorder side)
AES/EBU ANALOG
CH1/2
VIDEO
IN
IN
AC IN
ON
Y
75?
CH3/4
IN
OFF
P B
CH1/2
REF VIDEO
OUT
IN
ON
P R
75?
CH3/4
OUT OPTION
OFF
Y 1 VIDEO
OUT
2
P B
(WFM)
3
P R
(SUPER)
SIGNAL
GND
SERVICE ONLY
75h
termination
ON
Note concerning tapes played back by this VTR
Use tapes which have been shot by a variable frame rate
camera.
Do not use tapes which are copies of shot tapes or
edited tapes. Doing so will cause the tape management
information to be lost, and normal conversion and
playback may not be possible as a result.
To convert a tape recorded at frame rates other than 24
fps (25/50 fps) into 1080/24 psf (1080/25 psf or 1080/
50i), use the frame rate converter (optional AJ-FRC27).
SD SDI signal
REMOTE
IN/OUT
75h
termination
OFF
Remote
signal
(9P)
REMOTE
IN/OUT
SD
SDI IN
REMOTE ANALOG
SDI
IN OUT
REMOTE IN/OUT PUSH PUSH PUSH
CH1 CH1 AUDIO AUDIO CH2 CH2 TC TC
IN IN
IN IN
1
REMOTE OUT
ACTIVE
PUSH PUSH PUSH
CH3 CH3 TC TC
CH4 CH4 THROUGH
OUT OUT
2
ENCODER REMOTE
3
PUSH PUSH PUSH (SUPER)
CH1 CH1 AUDIO AUDIO CH2 CH2 MON MON
RS-232C OUT OUT L L
OPTION
SDTI
IN OUT
PARALLEL
PUSH PUSH PUSH
MON MON
CH3 CH3 CH4 CH4
R R 1
2
Video monitor