Diag - Panasonic DVCPRO HD AJ-HD1800P Operating Instructions Manual

Function menus
<DIAG>
This enables confirmation of information such as the
warning/hour-meter/UMID.
Verification, deletion of the error log file, retention/call to the
SD memory card can do with the SHIFT picture.
Warning mark
SHIFT F1 F2 F3
Warning display
When a warning occurs in this VTR, the warning mark (W)
blinks at the top left of the screen. If
pressed, the details of the warning can be checked out on
the LCD monitor.
When more than one warning has occurred, turn the ADJ
dial to scroll through the messages.
Hour-meter display
When (HOURS) is pressed, the hour-meter information
F2
can be checked out on the LCD monitor.
UMID display
Press (UMID) to confirm the current UMID information
F2
for the image on the LCD monitor.
DIAG-MENU
MATNO 0 0 0 0 1 2 3 4 0 0 5 6 7 8 B A
0 0 B 0 4 5 8 2 0 1 0 0 0 0 0 1
COPY
0
OWNR JP N :O RG : US ER
±3 7 7 5 m
POS
E 1 8 0 ' 0 0 ' 0 0 . 0 '
N 9 0 ' 0 0 ' 0 0 . 0 '
DATE
JA N- 2 8 - 0 2
TIME 2 3 : 3 0 :3 0 +0 3 h 0 0 m
DIF Status display
Press (DIF1) or (DIF2) to display the different kinds
F5
F4
of information about the current DIF (IEEE 1394 interface).
DIAG-MENU DIF STATUS 1
NODE CNT 1
MY ID 0
ROOT ID 0
IRM ID 0
RCV ID 0
GAP CNT 63
EUI-64 0080458200000000
Error log function
The error log mode can be selected by pressing the
button and switching the screen to <DIAG SHIFT>.
SHIFT F1 F2
(continued)
F4 F5 F6
(WARN) is now
F1
UMID INFO
3 D
DIAG-MENU DIF STATUS 2
<INPUT> <OUTPUT>
FMT FMT HD100
RATE RATE 1X
N/P N/P NTSC
CHN 63 CHN 63
SPEED SPEED 400
STAT STOP START OK
VIDEO VIDEO OK
AUDIO AUDIO OK
SHIFT
F3 F4 F5 F6
General description
When the following warnings have occurred while the tape is
running, the warning messages, time codes and operating
modes are saved, and a list of this information can be read
out on the LCD monitor. Up to 99 warnings which have
occurred can be saved.
warnings is exceeded, the processing that is conducted as a
result is based on the setup menu item No.015 (AUTO
STEP) setting.
Warning messages
which are saved
(Refer to page 129 and following.)
NO RF A blank section on the tape lasting more than
1 second has been detected. (During normal
playback)
SV NOT LOCKED The servo has been disengaged for more
than 3 seconds. (During recording, normal
playback or editing)
LOW RF An envelope level which is about 1/3 of nor-
mal or a CTL level which is about 1/6 of nor-
mal has been detected for more than 1
second. (During recording, normal playback
or editing)
HIGH ERROR RATE The error rate has deteriorated, and correc-
tion or compensation has been applied to the
video or audio playback signals. (During nor-
mal playback)
LCD monitor displays
Operation mode display
Saved warning status display
Warning display
Operation mode display
This indicates the operation mode at the point when the
warning was saved.
Warning display
This indicates the warning message which is saved.
Saved warning status display
This indicates the number of the currently displayed warning
which has been saved and the total number of warnings
which have been saved.
Time code display
This indicates the time code at the point when the warning
was saved.
Cueing up the tape to the warning point
The warning list displayed on the LCD monitor can be
scrolled by turning the ADJ dial.
occurrence point to be checked is selected and the
PREROLL button is pressed, the tape is cued up to the
position of the time code which has been saved.
If the storage capacity of 99
Description
Time code
display
When the warning
57