Parameter List - ABB PST30 Installation And Commissioning Manual

Param. Description
number
1 Setting current
2 Start ramp
3 Stop ramp
4 Initial voltage
5 End voltage
6 Step down voltage
7 Current limit
8 Kick start
9 Kick start level
10 Kick start time
11 Start ramp range
12 Stop ramp range
13 Overload protection type
14 Overload protection class
15 Overload class, dual type, start class
16 Overload class, dual type, run class
17 Overload protection, type of operation
18 Locked rotor protection
19 Locked rotor protection level
20 Locked rotor protection time
21 Locked rotor protection, type of operation
22 Underload protection
23 Underload protection level
24 Underload protection time
25 Underload protection, type of operation
26 Phase imbalance protection
27 Phase imbalance protection level
28 Phase imbalance protection, type of opera-
tion
29 High current protection
30 High current protection, type of operation
31 Phase reversal protection
32 Phase reversal protection, type of operation
33 PTC protection
34 PTC protection, type of operation
35 External by-pass
37 High current warning
38 High current warning level
39 Low current warning
40 Low current warning level
41 Overload warning
42 Overload warning level
43 Thyristor (SRC) overload warning
44 Phase loss fault, type of operation
45 Fieldbus fault, type of operation
46 Frequency fault, type of operation
47 Heat sink over-temperature fault, type of
operation
48 Thyristor short circuit fault, type of operation
49 Function of programmable input In0
1SFC132003M0201

7:1.2 Parameter list

Display text
Setting Ie
Start Ramp
Stop Ramp
Init Volt
End volt
Step down
Current Lim
Kick Start
Kick Level
Kick Time
Start Range
Stop Range
Overload
OL Class
OL Class S
OL Class R
OL Op
Locked Rotor
Lock R Lev
Lock R Time
Lock R Op
Underload
Underl Lev
Underl Time
Underl Op
Phase Imb
Ph Imb Lev
Ph Imb Op
High I
High I Op
Phase Rev
Ph Rev Op
PTC
PTC Op
Ext ByPass
Warn I=High
Wa I=H Lev
Warn I=Low
Wa I=L Lev
Warn OL
Wa OL Lev
Warn SCR OL
Ph Loss Op
FB Fault Op
Freq F Op
HS Temp Op
SCR SC Op
In0
Settings and configuration
Setting range
9.0...1207A
1...30s, 1...120s
0...30s, 0...120s
30...70%
30...70%
30...100%
2.0...7.0xle
Yes, No
50...100%
0.1...1.5s
1-30s, 1-120s
0-30s, 0-120s
No, Normal, Dual
10A, 10, 20, 30
10A, 10, 20, 30
10A, 10, 20, 30
Stop-M, Stop-A, Ind
Yes, No
0.5...8.0xle
0.2...10s
Stop-M, Stop-A, Ind
Yes, No
0.4...0.8xle
1...30s
Stop-M, Stop-A, Ind
Yes, No
10...80%
Stop-M, Stop-A, Ind
Yes, No
Stop-M, Stop-A, Ind
Yes, No
Stop-M, Stop-A, Ind
Yes, No
Stop-M, Stop-A, Ind
Yes, No
Yes, No
0.5...5.0xle
Yes, No
0.4...1.0xle
Yes, No
40...99%
Yes, No
Stop- M, Stop-A
Stop- M, Stop-A
Stop- M, Stop-A
Stop- M, Stop-A
Stop- M, Stop-A
None, Reset, Enable
Jog, DOL, Start 2, FB-
Dis
Chapter 7
Default Actual
value setting
Individual
10s
0s
30%
30%
100%
4.0xle
No
50%
0.2s
1-30s
0-30s
Normal
10
10
10
Stop-M
No
4.0xle
1.0s
Stop-M
No
0.5xle
10s
Stop-M
No
80%
Stop-M
No
Stop-M
No
Stop-M
No
Stop-M
No
No
1.2xle
No
0.8xle
No
90%
No
Stop-M
Stop-M
Stop-M
Stop-M
Stop-M
Reset
81