Samsung SPC-7000 User Manual

Samsung SPC-7000 User Manual

Network contoller


User Manual


Table of Contents

Summary of Contents for Samsung SPC-7000

  • Page 1 NETWORK CONTROLLER User Manual SPC-7000...
  • Page 2 Network Controller User Manual Copyright ©2016 Co., Ltd. All rights reserved. Hanwha Techwin Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
  • Page 3: Important Safety Instructions

  • Page 4 overview Please read the following recommended safety precautions carefully. y Do not place this apparatus on an uneven surface. y Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. y Do not place this apparatus near conductive material.
  • Page 5: Table Of Contents

    contentS overview controL Important Safety Instructions Control Cameras Contents Control Storage Devices Key Features What’s Included Part Names And Functions appenDiX Specifications Q & A inStaLLation Precautions GPL/LGPL Software License Before Installation Assemble Jog Shuttle/Joystick Adjust LCD Screen Angle Switching the Layout of Joystick and Jog Shuttle confiGure SettinGS Install...
  • Page 6: Key Features

    Key featureS wHat’S incLuDeD The SPC-7000 network controller controls network cameras and the SSM program using the Unpack the product package and place the product on the floor or a flat surface. network. Check if the following components are all included in the product package.
  • Page 7: Part Names And Functions

    part nameS anD functionS Name Function When you click a [PRESET] + number + [PRESET] button, the front Side [PRESET] preset corresponding to each button number is activated. When you click a [GROUP] + number + [GROUP] button, [GROUP] Group/Scan corresponding to each button number is activated.
  • Page 8 overview rear Side Name Function Changes the PTZ mode. [PTZ(MENU)] Click the [PTZ (MENU)] button while in PTZ mode and the screen mode will be changed. Changes the mouse mode. Mode PORT 1 & [SHIFT] + [MENU(Mouse)] Click the [SHIFT] + [MENU (Mouse)] buttons while in mouse PORT 2 RESERVED NETWORK...
  • Page 9: Precautions

    installation precautionS Before inStaLLation Before you install the product, read through and comply with the following instructions. • You must turn off the product before installing it. • The product is designed for indoor use only. • A severe impact or vibration may cause a system failure. • Keep it away from water or moisture.
  • Page 10: Assemble Jog Shuttle/Joystick

    installation aSSemBLe JoG SHuttLe/JoySticK SwitcHinG tHe Layout of JoySticK anD JoG SHuttLe When assembling the jog shuttle or joystick, press it until you hear a clicking sound. For convenience you can switch the position of joystick and jog shuttle module. To switch between left and right, turn off the system controller and switch the modules manually.
  • Page 11: Configure Settings

    configure settings inStaLL GettinG StarteD 1. With the computer turned on, connect the 1. Turn on all system component devices. SSM terminal of the controller to the USB 2. Connect the power adapter on the back of port of the computer. the controller and turn it on.
  • Page 12: Configure Menu

    configure settings confiGure menu 3. Enter an <iD> and <password> and press the <teSt> button to access the camera. When the system settings screen appears, select 4. Press the <oK> button and the selected your desired settings item. camera will be registered. • Model: Shows the camera model name.
  • Page 13: Control

    user & password modify Device information You can modify the information of a registered device. You can change the administrator’s password and grant a device ID. 1. Select a device to change the information. to add a user 2. In the device information section displayed at 1.
  • Page 14: Network

    configure settings SyStem environment Joystick Button operation The joystick button is operated only by the You can update the current firmware using the firmware files in the USB memory. <enter> function. to update the controller firmware You can download the latest firmware files and update the controller. 1.
  • Page 15 to backup the controller settings If you want to change the controller or replace the camera, you can save the settings of the controller as a file and load the controller settings into a new camera. 1. From the menu setup screen, press <System>. 2.
  • Page 16: Control Cameras

    control controL cameraS control cameras Press the [af] key on the controller and the camera autofocus will be activated. You can configure a camera, storage device and settings menu. For more information about the camera control, refer to the “Part Names And Functions” section. If the version of SUNAPI of a network camera registered, a specific function may not work.
  • Page 17 Group tour You can make a group of multiple presets before calling them in sequence. You can make a tour of at least one group before executing the groups in sequence. You can designate up to 6 groups. to set a tour A single group can contain up to 128 presets.
  • Page 18 control Swing trace You can move the camera between two preset points to monitor the course. With the joystick or camera buttons, you can instruct the controller to record the camera movement for a specific time and repeat the movement. Swing setup to set a trace 1.
  • Page 19: Control Storage Devices

    controL StoraGe DeviceS auto tracking You can select whether to enable/disable the As functions vary depending on the device, please refer to the user manual for the device. auto tracking function of a camera that supports this function. You can control the storage devices registered in the SSM by selecting the SSM.
  • Page 20 control PTZ control Screen control You can change the multi monitor selection by clicking a number + [MON. Runs the Focus Near/Far motion. [FOCUS N/F] + (CON.)] button in the screen mode (previous/next according to the monitor [MON.(CON.)] - [FOCUS N/F] + : Focus Near number).
  • Page 21 Gui control mode Play screen control 1. Press [SHift], [recorDer/SSm]. Outputs the video of the current tile through live/search. [SEARCH] 2. Select <console>, <virtual mode>. If you select either console or virtual mode, The video will be stopped. configurable sub functions will be enabled. • Device ID : Disabled when controlling the Plays and pauses the video.
  • Page 22 control recording Starts or stops recording. Search Displays a playback video. Snapshot Saves a captured image. The image will be saved on the PC where the SSM is installed. alarm off Turns off an event alarm. 22_ control...
  • Page 23: Specifications

    Q & a Item Description Problem Action Communication System • Check the cable connection between SPC-7000 and the PC. Unable to communicate with the RJ-45(Ethernet) controller. • Confirm that the IP address of the network controller is correct. Units to control Max. 255...
  • Page 24: Gpl/Lgpl Software License

    GpL/LGpL Software LicenSe These requirements apply to the modified work as a whole. If identifiable You may not impose any further restrictions on the recipients' exercise of sections of that work are not derived from the Program, and can be the rights granted herein.
  • Page 25 Gnu GeneraL puBLic LicenSe 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR “The Program” refers to any copyrightable work licensed under this License. You may make, run and propagate covered works that you do not convey, AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR Each licensee is addressed as “you”.
  • Page 26 a) Convey the object code in, or embodied in, a physical product (including Corresponding Source conveyed, and Installation Information provided, in of this License (for any work) from that copyright holder, and you cure the If, pursuant to or in connection with a single transaction or arrangement, you a physical distribution medium), accompanied by the Corresponding accord with this section must be in a format that is publicly documented (and violation prior to 30 days after your receipt of the notice.
  • Page 27 4. You may copy and distribute the Library (or a portion or derivative of EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED To protect each distributor, we want to make it very clear that there is no “Source code” for a work means the preferred form of the work for WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR warranty for the free library.
  • Page 28 enD of termS anD conDitionS c) Accompany the work with a written offer, valid for at least three years, It is not the purpose of this section to induce you to infringe any patents to give the same user the materials specified in Subsection 6a, above, or other property right claims or to contest validity of any such claims;...
  • Page 29 Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 30 Head Office 86 Cheonggyecheon-ro Jung-gu Seoul 04541 Korea Tel +82.2.729.5277, 5254 Fax +82.2.729.5489 Hanwha Techwin America 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 Hanwha Techwin Europe 2nd Floor, No. 5 The Heights, Brooklands, Weybridge, Surrey, KT13 0NY, UK Tel +44.1932.82.6700 Fax +44.1932.82.6701...

Table of Contents