Roundup’s strict quality standards. This unit has been tested at the factory to ensure depend- The warranty does not extend to: able trouble-free operation.
Service/Technical Assistance Refer to the service agency directory included with your unit. If you experience any problems with the installation or operation of your unit, contact your local Roundup Authorized Service Agency Authorized Service Agency. Name: Fill in the information below and have it handy when Phone No.:...
Page 4
• This equipment should be serviced by qualified similarly qualified person. personnel only. Contact the nearest Roundup authorized service facility for adjustment or repair. • All electrical connections must be in accor- dance with local electrical codes and any •...
VERTICAL CONTACT TOASTER INSTALLATION Unpacking 7. Install power cord to the bottom of unit (Figure 1) (Mfg. No. 9200580 only). 1. Remove unit and all packing materials from ship- ping carton. Bun Feeder #9200582 only 2. Open the included large box. It should contain the following: •...
VERTICAL CONTACT TOASTER INSTALLATION (continued) Equipment Setup When placing the toaster into service, pay attention to the following guidelines. Feeder #9200582 • Make sure power to the unit is off and the toaster only is at room temperature. Heat Shield •...
Hi-Limit Reset display and the unit is ready to toast buns. If “USE” does not appear in the window after warm-up period of approximately 30 minutes, contact your Roundup authorized service agency. Temperature Controls & 3. Drop buns into toaster (Figure 4). Cut sides of...
Page 9
VERTICAL CONTACT TOASTER OPERATION (continued) TEMPERATURE CONTROL PANEL “Heat On” LED will blink on/off during warm-up and when either platen or auxiliary heaters are calling for heat. NOTE: Setpoint Temperature refers to the desired tem- perature setting. Pressing the TEMP UP key will display the current plat- SP - P en heater temperature providing the platen temperature is over 440°F (227°C).
VERTICAL CONTACT TOASTER OPERATION (continued) 1. Press both keys at the same 1. Press both keys at the same time for 1 second to start time for 1 second to start adjustment sequence. adjustment sequence. °F °F 2. Press TEMP UP key to raise 2.
VERTICAL CONTACT TOASTER OPERATION (continued) Fault Codes If the toaster control board If the toaster control board resembles the OLD style resembles the NEW style NEW STYLE OLD STYLE shown here, refer to the shown here, refer to the CONTROL BOARD CONTROL BOARD Fault Message in Table 1.
VERTICAL CONTACT TOASTER MAINTENANCE 7 Turn Rocker Switch (power on/off) to OFF and WARNING unplug the power cord. Turn the unit off, disconnect the power source and allow the unit to cool down before performing 8. Wipe down the outside of the toaster and all the any service or maintenance on the unit.
VERTICAL CONTACT TOASTER MAINTENANCE (continued) Replacing Belt Wraps Interlock Switch 1. Turn rocker switch (power on/off) to OFF, unplug the power cord and allow the unit to cool down before proceeding. Conveyor 2. Remove the heat shield, Open the front conveyor Cover Assy.
VERTICAL CONTACT TOASTER MAINTENANCE (continued) Stainless Steel Conveyor Belts Rotation Upper Support Rod WARNING Turn the unit off, disconnect the power source and allow the unit to cool down before performing any service or maintenance on the unit. SERVICING CONVEYOR BELTS After a period of time, the conveyor links will wear and Large Link the conveyor belt will stretch, eventually causing buns...
VERTICAL CONTACT TOASTER TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equip- ment should be performed by qualified service personnel. The unit should be unplugged when servicing, except when electrical tests are required. Use extreme care during electrical circuit tests. Live circuits will be exposed.
VERTICAL CONTACT TOASTER TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action Buns are sticking (contin- Conveyor Belt not turning, Verify Motor Chain is attached. Contact your ued). Conveyor Chain not turning. maintenance person or Authorized Service Agency. Buns are not toasting prop- Compression settings incorrect.
This warranty does not cover Travel Time & Mileage in excess of 2 hours (100 miles/160 km) round trip from the nearest authorized service agency. 2. Roundup reserves the right to make changes in design or add any improvements on any product. The right is always reserved to modify equipment because of factors beyond our control and government regulations.