Roundup VCT-1000 Owner's Manual

Roundup VCT-1000 Owner's Manual

Vertical contact toaster
Hide thumbs Also See for VCT-1000:

Advertisement

MANufActuRiNg
NuMbeRs:
9210719
9210721
Vertical contact
toaster
With Mechanical Driven Butter Wheel
CM
Models VCT-1000
P/N 1010930 Rev. A 06/08
owner
s Manual
'

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VCT-1000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Roundup VCT-1000

  • Page 1 MANufActuRiNg NuMbeRs: 9210719 9210721 Vertical contact toaster With Mechanical Driven Butter Wheel Models VCT-1000 P/N 1010930 Rev. A 06/08 owner s Manual ’...
  • Page 2: Table Of Contents

    15 seconds (Vct-1000) or 45 seconds NOt covered under warranty. (Vct-50). the warranty does NOt extend to: this manual provides the safety, installation, and oper- ating procedures for the Vertical contact toaster.
  • Page 3: Service/Technical Assistance

    Owner infOrmatiOn (continued) service/technical assistance Authorized service Agency if you experience any problems with the installation Name: or operation of your unit, contact your local Roundup Phone No.: Authorized service Agency. Address: fill in the information below and have it handy when calling your Authorized service Agency for assistance.
  • Page 4: Important Safety Information

    • All electrical connections must be in accordance with local electrical codes and any other appli- • This equipment should be serviced by qualified cable codes. personnel only. contact the nearest Roundup Authorized service Agency for adjustment or • WARNINg elecTRIcAl ShOcK hAzARD. repair.
  • Page 5: Specifications

    Vertical contact toaster specificatiOns model Designation electrical ratings model & Vct-1000XX Volts watts amp. Hertz mfg. no. type Of pOwer cOrD Vct-1000cV 208– 2600– 12.5– c = cOMMeRciAL 9210719 & 3455 14.4 9210721 type Of plUG electrical cord & plug configurations V = NeMA 6-20P model &...
  • Page 6: Installation

    Vertical contact toaster installatiOn assembling the Unit Unpacking nOte: the factory has a pre-installed a release 1. Remove unit and all packing materials from sheet over the platen (figure 1). Verify that it is shipping carton. properly in place before proceeding. 2.
  • Page 7 Rear conveyor belt chain conveyor Yellow safety support interlock switch front conveyor belt chain Rear conveyor cover Assembly spring tensioner Assembly front conveyor cover Assembly bun chute figure 1. Vct-1000 with mechanical Driven butter wheel P/N 1010930 Rev. A 06/08...
  • Page 8: Operation

    Vertical contact toaster OperatiOn Operating instructions bun thickness Adjustment controls impOrtant (see figure 3) Verify that the Release sheet is installed completely over the Platen (figure 1) before proceeding. failure THICKNESS THICKNESS Hi-Limit Reset to use Release sheet may cause permanent damage to the Platen surface that is not covered by warranty.
  • Page 9: Maintenance

    Vertical contact toaster maintenance 7. Wipe down the outside of the toaster with a caUtiOn clean, damp, sanitized towel. turn the power off, unplug the power cord, and allow 8. install the Release sheet by draping it over both the unit to cool down 30 minutes before performing sides of the Platen with the crease centered on any service or maintenance.
  • Page 10: Checking The Conveyor Belt Chains

    Vertical contact toaster maintenance (continued) checking the conveyor belt chains (every 3–6 months) nOte: the bun thickness compression Knobs (figure 3) must be set to “6 & 6” prior to measur- ing or removing or reinstalling the conveyor belt chains. measUrinG cOnVeyOr belt cHains 1.
  • Page 11: Replacing The Spring Tensioners

    Vertical contact toaster maintenance (continued) replacing the spring tensioners replacinG cOnVeyOr belt cHains 1. turn the power off, unplug the power cord, and 1. Remove the Acorn Nuts (figure 7). allow the unit to cool before proceeding. 2. Remove the old spring tensioner Assembly. 2.
  • Page 12: Troubleshooting

    Vertical contact toaster trOUblesHOOtinG warninG to avoid possible personal injury and/or damage to the unit, inspection, test, and repair of electrical equipment should be performed by qualified service personnel. the unit should be unplugged when servicing, except when electrical tests are required. use extreme care during electrical circuit tests. Live circuits will be exposed. problem possible cause corrective action...
  • Page 13 Vertical contact toaster trOUblesHOOtinG (continued) problem possible cause corrective action Product is over toasted temperature set too high. set temperature control to a lower setting. or Platen heat is too bun thickness compression Measure bun thickness and set bun thickness high or drop time is too Knobs set improperly.
  • Page 14: Wiring Diagram

    Vertical contact toaster wirinG DiaGram pictorial wiring Diagram Vct-50 & Vct-1000 POWER CORD NOTE: ALL WIRES TO BE 14 GA. AWM-105°C UNLESS OTHERWISE SPECIFIED. * 16 GA. TFE-200°C = 18 GA. AWM-105°C # 16 GA. AWM-105°C % 14 GA. TFE-200°C...
  • Page 15: Replacement Parts

    Vertical contact toaster replacement parts parts identification interlock switch Drive chain idler sprocket Front Drive Rear Drive sprocket sprocket temperature control thermostat fan blade Power switch Hi-Limit control Drive Motor Assy. P/N 1010930 Rev. A 06/08...
  • Page 16 Vertical contact toaster RePLAceMeNt PARts (continued) P/N 1010930 Rev. A 06/08...
  • Page 17 Vertical contact toaster RePLAceMeNt PARts (continued) P/N 1010930 Rev. A 06/08...
  • Page 18 Vertical contact toaster RePLAceMeNt PARts (continued) 30, 94 31, 95 P/N 1010930 Rev. A 06/08...
  • Page 19 Vertical contact toaster RePLAceMeNt PARts (continued) item part no. Description Qty. item part no. Description Qty. 0011266 conveyor belt chain 100P864* Label, caution Hot (incl. items below) 310P109* screw, Hex, #10-32 x 3/8” 0800204 1/2” Pitch Link, small 304P105* Nut, #4-40, “KePS” 0800121 3/4”...
  • Page 20: Limited Warranty

    2. Roundup reserves the right to make changes in design or add any improvements on any product. the right is always reserved to modify equipment because of factors beyond our control and government regu- lations.

This manual is also suitable for:

Vct-50

Table of Contents