Denon UD-M31 Operating Instructions Manual page 13

Manual tuning
CD RECEIVER UD-M31
ON / STANDBY
1
Example: Tuning in FM 92.50 MHz
(AM stations are tuned in using the same procedure.)
Press the power operation switch to turn on the
1
power.
Press the FUNCTION button to select TUNER
2
mode.
Press the BAND button on the tuner to select the
3
FM AUTO.
Use the Tuning +/– button to tune the frequency to
✽
92.50. Once the frequency is tuned in, adjust the
4
volume to the desired level using the VOLUME
control.
✽ The function of the +/– button on the main unit may toggle between Tuning +/– and Preset +/– functions.
• Pressing the – button while holding down the BAND button at the same time changes function of the +/– button to
Tuning +/–. ("TUNING" flashes for 5 seconds.)
• Pressing the + button while holding down the BAND button at the same time changes the function of the +/– button
to Preset +/–. ("PRESET" flashes for 5 seconds.)
• The +/– button is factory preset to function as a Tuning +/– button.
However, be sure that the +/- buttons function as the Tuning +/– button before proceeding with step 4.
Auto Tuning
• When a program being broadcast in stereo is received, the "ST" indicator lights and the program is received in stereo.
• If reception is poor and there is much noise in the stereo signals, press the BAND button to set the FM MONO mode.
• When one of the Tuning +/– button is pressed, the frequency changes in steps of 50 kHz in the FM band, 9 kHz in the
AM band.
• If one of the Tuning +/– button is held for over 1 second, the frequency continues to change when the button is
released (auto tuning) and stops when a station is tuned in. Tuning will not stop at stations whose reception is poor.
• To stop the auto tuning function, press the Tuning +/– button once.
NOTE:
• A humming sound may be heard when using a TV nearby while receiving AM programs. If this happens, move the
system as far from the TV as possible.
3 4
BAND
- +
MENU / SET
TONE/SDB
VOLUME
FUNCTION
PHONES
2
ON / STANDBY
FUNCTION
BAND
This lights when a station is tuned in.
+
-
Presetting or naming radio stations
(This operation is only possible from the remote control unit.)
You can preset up to 40 FM/AM stations.
You can name the preset stations (up to 8 characters each).
1
Tune in the desired preset station.
Press the EDIT button on the remote control unit.
2
• You can now begin character input.
Press the +/– button until the desired character
appears on the display. Press the ENTER/MEMORY
button on the remote control unit to store the input
character.
• Press the 7 button or the ENTER/MEMORY
3
button to store the input character. The cursor will
move to the next character space. Repeat step 3
until all the characters have been stored.
• You can move the cursor backward by pressing
the 6 button to make corrections.
Press the EDIT button to confirm the names of the
preset stations.
4
• The preset number is displayed. "MEMO" and
"P. SET" indicator flashes for 10 seconds.
Press the +/– button on the remote control unit to
5
tune in the desired preset number.
Press the ENTER/MEMORY button to confirm the
6
preset station number.
• To discontinue the procedure, press the CLEAR button on the remote control unit before proceeding to step 4.
• To erase a preset station name, press the PRESET •/ª to display the preset station you want to erase, then press
EDIT and CLEAR. The preset station name is erased, and only the preset frequency appears on the display.
• To preset only the frequency of the radio station, start over from step 1. Then press the ENTER/MEMORY button and
proceed to steps 5 through 6. The display shows the preset number, band and frequency.
ENGLISH
EDIT
Flashes
PRESET
+
-
ENTER/MEMORY
ENTER
MEMORY
Next flashes
EDIT
Flashes
PRESET
- +
Flashes
ENTER
MEMORY
13