Icom IC-7850 Instruction Manual page 274

INDEX
Symbol
∂F scan ................................................................ 12-9
∂TX function ........................................................... 8-5
Monitor function ................................................. 8-5
Number
1⁄4 tuning step function ........................................... 4-9
1.2 kHz Filter calibration ......................................... 7-8
137 kHz band operation ......................................... 5-8
5 MHz frequency band operation ......................... 4-18
ABOUT THE SUPPLIED CD .....................................iv
About the VOX function .......................................... 8-2
ACC set screen .............................................2-8, 15-6
ACC socket ........................................................... 20-2
ACC1 ............................................................... 20-2
ACC2 ............................................................... 20-2
Advanced connections ........................................... 3-5
AFC/NET function ................................................. 5-28
AGC
AGC function control ......................................... 7-4
AGC time constant ............................................ 7-4
Setting the AGC time constant preset value ...... 7-4
AM mode
Operating AM or FM ........................................ 5-36
Antenna connection and selection ........................ 13-2
Antenna Memory ..................................................
Antenna memory settings ..................................... 13-3
Antenna selection mode ....................................... 13-5
Antenna tuner ..............................................13-7, 19-3
Using the Antenna tuner operation .................. 13-7
If the tuner cannot tune the antenna ............... 13-8
Antenna type ...............................................2-16, 13-4
Selecting the antenna type .............................. 13-4
APF (Audio Peak Filter) operation .......................... 5-6
Attenuator ............................................................... 7-2
Audio scope screen .............................................. 6-15
AUDIO SCOPE SET .......................................... 2-6
Audio scope set mode ..................................... 6-16
FFT Scope
FFT Scope Waterfall Display ...................... 6-16
FFT Scope Waveform Color ....................... 6-16
FFT Scope Waveform Type ........................ 6-16
Oscilloscope
Oscilloscope Waveform Color ..................... 6-16
Audio level .............................................................. 4-4
Automatic transmission/reception setting ....5-18, 5-30
Auto notch function ............................................... 7-13
Auto tuning step function ........................................ 4-8
A
Averaging .............................................................. 6-10
Band edge warning beep...................................... 4-15
Entering the user band edge ........................... 4-16
Register the Band edge ................................... 4-16
User band edge ............................................... 4-15
Band stacking registers .......................................... 4-6
Band selection
Selecting the Main and Sub bands .................... 4-5
BPSK and QPSK modes ...................................... 5-27
BPSK31 and BPSK63 modes ............................... 5-27
Break-in function ..................................................... 8-4
Full break-in operation ....................................... 8-4
Semi break-in operation .................................... 8-4
Calibration the Frequency (approximate) ............. 16-4
Capture list screen .............................................. 10-10
Checking the firmware version ............................. 17-2
Checking the repeater input signal ....................... 5-37
CI-V
CI-V Address ...................................................
CI-V connection ............................................... 18-2
Command table ............................................... 18-3
Data content description ................................ 18-10
Data format ...................................................... 18-2
Preparing ......................................................... 18-2
10-4
Cleaning ............................................................... 16-7
Clock
Entering the CLOCK2 Name ........................... 14-3
Selecting the CLOCK2 Function ..................... 14-3
Setting the CLOCK2 UTC Offset ..................... 14-3
Setting the Current time .................................. 14-2
Setting the Date ............................................... 14-2
Clock backup battery replacement ....................... 16-9
Confirming programmed memory channels ......... 11-3
Connecting a non-Icom linear amplifier .................. 3-7
Connecting antenna ............................................... 3-3
Connecting the IC-PW1/EURO .............................. 3-7
Connections
Advanced connections ...................................... 3-5
Required connections ........................................ 3-4
Connector
Microphone connector ..................................... 20-3
[REF I/O] connector ......................................... 20-4
[RX-I/O] connector ........................................... 20-5
[X-VERTER] connector .................................... 20-4
Contest number set mode .................................... 5-12
Convenient functions for Receive ........................... 5-2
Convenient functions for Transmit ........................... 5-3
I-1
B
C
10-4