Service And Support; Fcc Compliance Statement - AIRTRONICS MT-S User Manual

MT- S
Telemetry System with Sanwa Synchronized Link Support
2.4GHZ FH4T RADIO SYSTEM USER'S GUIDE

SERVICE AND SUPPORT

This product is warranted against manufacturer defects in materials and workmanship, at the original date of purchase. This
warranty does not cover components worn by use or damage caused by improper voltage, tampering, modification, misuse,
abuse, improper wiring, reverse polarity, moisture or using outside its intended scope of use.
Terms of this warranty can vary by region. Please read the warranty card included
If you have any questions or concerns, we're here to help. If you encounter a problem with your radio control system, first check
the Troubleshooting Guide section on pages 65 and 66.
If you require further help that cannot be solved using the Troubleshooting Guide, or if you have technical questions, please
contact the Airtronics or Sanwa service center in your region.
For a complete list of distributors in your region, please visit www.sanwa-denshi.com/rc/distributors.html.
Product features and specifications can vary by region. Not all products are legal for use in all regions.
Please note that products purchased outside of North America cannot be serviced under warranty by Global Services.
In some cases, we can make repairs for products purchased outside of North America, however, applicable repair costs
and shipping charges will be applicable. For warranty claims outside of North America, please contact the service center in
your region.

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the operating instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: (A)
Reorient or relocate the receiving antenna, (B) Increase the separation between the equipment and the receiver, (C) connect
the equipment into an outlet on a circuit different from that to which the receiver is connected and/or (D) consult the dealer or
an experienced technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and...
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada's license-exempt RSSs, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and...
(2) This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et...
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Changes or modifications made to this equipment not expressly approved by Airtronics may void the FCC
authorization to operate this equipment.
RF Exposure Statement:
This transmitter has been tested and meets the FCC RF exposure guidelines when used with the Airtronics accessories supplied
or designated for this product, and provided at least 20cm separation between the antenna the user's body is maintained. Use
of other accessories may not ensure compliance with FCC RF exposure guidelines.
4
with your radio control system for specific warranty information.
For Service In North America:
Global Services/Airtronics
18480 Bandilier Circle
Fountain Valley, CA 92708
Telephone: (714) 963-0329
Fax: (714) 964-6236
Email: service@airtronics.net
Factory Service:
Sanwa Electronic Instrument CO., LTD.
1-2-50 Yoshida-Honmachi
Higashiosaka, Osaka, 578-0982 Japan
Telephone: 81-729-62-1277
Fax: 81-729-64-2831
Email: rcintl@sanwa-denshi.co.jp
GENERAL
GENERAL