Related Manuals for Sartorius PMA 7501-X
Summary of Contents for Sartorius PMA 7501-X
- Page 1 Installation Instructions Sartorius PMA.Quality PMA 7501-X|PMA 7501-X00V1|PMA 7501-X00W Electronic Paint-mixing Scales for Zone 1 98648-014-43...
-
Page 2: General View Of The Equipment
5 U key: Zero/Tare 14 Grounding terminal 6 I key (TOGGLE) 15 Column With the PMA 7501-X, you can toggle 16 Joint to two decimal places – from 0.05 g to The following symbols are used in 999.95 g – or toggle between – “g” and these instructions: “p”... -
Page 3: Table Of Contents
Contents Warnings and Safety Precautions Note: General View of the Equipment ..2 Improper use or handling can result in Intended Use ....3 property damage and/or personal injury. - Page 4 – If the equipment housing is opened by in the cable against those specified by anyone other than persons authorized by Sartorius before connecting the cable to Sartorius, this will negate its conformity Sartorius equipment, and disconnect any with regulations governing its use and wires that are assigned differently.
- Page 5 Handle the equipment and – Use original Sartorius spare parts only. any accessories in accordance with the IP – Never use a hammer to close the lid of a rating (IP65 or higher) and EN 60529.
-
Page 6: Getting Started
Getting Started § Remove the scale from its packaging. § After unpacking the scale, check it immediately for any visible damage as a result of rough handling during shipment. Equipment Supplied – Scale – Weighing pan – Power supply Setting Up the Scale Choose a suitable place to set up the scale. - Page 7 If you should have any questions, please contact your supplier or Sartorius Customer Service for information on the legal regulations applicable in your country. Use only genuine Sartorius power supplies. The use of power supplies from other manufacturers, even if these units have a registered approval rating from a national testing laboratory, requires the approval of a certified technician.
-
Page 8: Operating The Equipment
Operating the Equipment Turn on the scale using the After the scale has been If a different readout is Q key (2). turned on, it will automati- displayed, zero or tare the cally run a self-test. scale using the U key (5). At the end of this test, 0.0 g is displayed. - Page 9 Weighing with Two Decimal Places Note: To weigh using two decimal places, you must first adapt the settings (refer to the chapter entitled “Menu Settings”) Press the I key (6). The display shows “0.00 g.” Place an empty paint can on the weighing pan (11). Press the U key (5).
-
Page 10: Applications
Applications Formulation Mode (Calculation by a Factor) This mode enables you to weigh in amounts that are smaller or larger than that of your basic formula for a specific paint color (e.g., 250 ml of a 1-l formula). You can select various factors (amounts) by pressing the K formulation key (7): 0.25 0.5 0.75 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0. - Page 11 3. “.25” is displayed next to the weight 4. Slowly pour in the first component, “250 g” of green paint, until the display shows “250 g.” 5. Pour in the second component, “250 g” of red paint, until the display shows “500 g.” 6.
- Page 12 Example (cumulative): Place an empty paint can on Press the U key (5) Pour in the first component. the weighing pan (11). 0.0 g + 50.0 g + 118.0 g Press the L key [MEM] (9). Pour in the 2nd component. Press the L key [MEM] (9).
-
Page 13: Calibration/Adjustment
Calibration/Adjustment You can calibrate/adjust the scale by pressing the U key (5). Calibration weight: 5,000 g; accuracy: + 0.075 g. After connection to AC power and before each calibration/adjustment, allow the scale to warm up for approx. 30 min. Hold down the U key (5) for 2 sec. When 5000 is displayed, release the key. -
Page 14: Menu Settings
§ Press the L key [ENTER]. “o” will appear. The new code is stored. § Press the c key (Clear) several times to exit the menu. Note: To obtain a detailed list of the menu codes, please ask your nearest Sartorius office. - Page 15 Important Menu Settings § Hold down the L key [ENTER] for approx. 2 sec. “SETUP” will appear on the display (Level 1). Level 1 SETUP Language Settings Level 1 Level 2 Level 3 Level 4 § R key: select “LANGUAGE” LANGUAGE §...
- Page 16 Toggling Decimal Places (Standard = 1 decimal place PolyRange = 2 decimal places) Toggling Units (Grams or PT./PD.) These settings are active when the scale is switched on. Level 1 Level 2 Level 3 Level 4 § Press the L key [ENTER] SETUP §...
- Page 17 Note: Keep the numeric code in a safe place. The scale can only be accessed by entering the correct code. Level 1 Level 2 Level 3 Level 4 § RS keys: select “INPUT” INPUT § Press the L key [ENTER] PASSWORD §...
- Page 18 § Press the L key [ENTER]; “o” will appear: etc. the new code is set § Press the c key (Clear) several times o CODES to exit the menu. Note: To obtain a detailed list of the menu codes, please ask your nearest Sartorius office.
-
Page 19: Troubleshooting
Troubleshooting Problem Cause Solution No segments appear – No AC power available – Check the AC power supply on the weight display Weight display shows – The weighing pan is – Position the weighing pan “Low” is not in place Weight display shows –... -
Page 20: Care And Maintenance
In this case, notify your nearest Sartorius $ Storage temperature: –20°C to +75°C Service Center or the International Tech- $ Permissible moisture level for storage of nical Support Unit based in Goettingen, the packaged scale: 90% max. -
Page 21: Recycling
EU: 1) Go to http://www.sartorius.com. 2) Select the summary under “Service.” 3) Then select “Information on Disposal.” 4) Addresses for local Sartorius disposal contacts can be found in the PDF files given on this webpage. -
Page 22: Specifications
Specifications Model PMA7501-X | -X00V1 | -X00W Weighing range 999.95/7500 Readability 0.05/0.1 Tare range (subtractive) -999.95/-7500 Max. linearity < ±0.2 Stability range digit 0.25 to 4 Moisture-proof rating Non-condensing Allowable ambient operating temperature range °C 0 to +40 Weighing pan d mm Scale housing (W + D + H) 233 + 329 + 391... -
Page 23: Accessories
Accessories Order no.: YDC01PMA In-use dust cover EX power supplies 609308-011 609308-211 609308-61 USA/CDN... -
Page 32: Verification Of Intrinsic Safety
1.61 W 575 nF 10 µF (for IIB) 420 µH 5 µH (for IIB) Non-hazardous area Sartorius cable; permanently Sartorius cable; permanently Hazardous area mounted on the power supply/ mounted on the power supply Zone 1 Ex-link box (max. length: 100m) (max. - Page 33 YDI05-Z.. Z966 in YDI02-Z.. YCO01-Y 12.4 V 12.6 V 12 V 11.8 V 12.6 V 24.8 V 25.2 V 23.6V 25.2 V 24 V 260 mA * 123 mA * 131mA 328 mA * 800 mW * 361 mW * 0.96 W * 1.24 µF 1.5 µF...
- Page 34 Ethernet or RS-232 data YCO11-Z interface EX-link box for connecting to equipment using 250V II (2)G [EEx ib] IIB power supply, maximum Sartorius cable; permanently mounted on the Ex-link box (max. length: 100m) Non-hazardous area Hazardous area Zone 1 Gas: IIB T4 TM01-X...
- Page 40 Sartorius Lab Instruments GmbH & Co. KG Weender Landstrasse 94–108 37075 Goettingen, Germany Phone +49.551.308.0 +49.551.308.32 89 www.sartorius.com Copyright by Sartorius Lab Instruments GmbH & Co. KG, Goettingen, Germany. All rights reserved. No part of this publication may be reprinted or translated in any form or by any means without the prior written permission of Sartorius.
Need help?
Do you have a question about the PMA 7501-X and is the answer not in the manual?
Questions and answers