Advertisement
Quick Links
Advertisement
Related Manuals for Contura C i10
Summary of Contents for Contura C i10
- Page 1 Installation Instruction C i10/ C i20 www.contura.eu...
- Page 2 Box 134, Skulptörvägen 10, SE-285 23 Markaryd Place of manufacture Markaryd, Sweden PrODuct Product type Insert lit with solid fuels type designation Contura Insert 10 and 20 Standard EN 13229 Intended for use Heating of living accommodation fuels Wood logs...
-
Page 3: Table Of Contents
A warm welcome to the Contura family. We hope you will get a great deal of pleasure from your new stove. As a new owner of a Contura stove, you have secured a product with timeless design and long service life. -
Page 4: General
This manual contains instructions about soot hatches must be easily accessible. mm thick metal. The floor in front of the how the Contura i10 and i20 must be hearth opening must be protected against constructed and installed. In order for any falling embers using non-flammable the Insert’s function and safety to be... -
Page 5: Important Dimensions
IMPORTANT DIMENSIONS Important dimensions C i10 Ø 200 Air inlet Ø100 C i20 Ø 200 Air inlet Ø100... -
Page 6: Prior To Installation
PRIOR TO INSTALLATION Prior to installation Unpacking and removing loose parts Before moving the insert, the loose parts inside the insert should be removed by removing the screws, which makes up the transport locking device for the hatch’s counter weight. Check that both wires are in the grooves for the sheaves before the hatch is opened and the loose parts can be removed. - Page 7 The hatch runners are lubricated at the factory, with special grease that can withstand high temperatures. This type of grease is usually difficult to find on the market and we recommend contacting a Contura dealer to order this special grease when lubricating the runners. Cleaning the hatch glass If necessary, the hatch can easily be cleaned of soot or ash.
- Page 8 PRIOR TO INSTALLATION Self-closing hatch The insert can be supplied with a self-closing hatch. First open the hatch according to section “Cleaning the hatch glass”, then remove the four screws to release the Upper member. Remove the two screws that hold the spring assembly, install the weight to the upper member and reinstall the spring assembly in the upper screw holes.
- Page 9 PRIOR TO INSTALLATION Start by placing the insulation panel in the bottom of the Insert. Start installing the two lower parts of the hearth surround, then continue with the left back section followed by the left side, finally install the right back section and side. Position the ash-pan and cast-iron grate.
-
Page 10: Installation
INSTALLATION Installation Ensure that the installation is approved by a certified chimney sweep, who can also provide information on which national and regional regulations apply. Also ensure that a function check of the hatch opening mechanism and damper control is performed according to the “Function check”... -
Page 11: Connection To Chimney
CONNECTION TO ChIMNEy Connection to chimney The insert is prepared for top connection, when connecting from the rear of the insert, the Ø200 connector and cover on the rear of the insert must be switched over, see “Connecting from the rear of the insert”. - Page 12 CONNECTION TO ChIMNEy Connecting from the rear of the insert Remove the top and rear panels. Swap the connector and cover. Install the connection pipe on the connector; ensure that gasket does not move out of position. When the insert is in position, seal the connection pipe and wall connector well, use heat-resistant sealant if necessary.
-
Page 13: Recessing The Insert
RECESSING ThE INSERT Recessing the insert When recessing the insert, adjacent walls that are not classed as fire walls or are considered unsuitable for heat loads must be protected by non-combustible material according to the specification below. All joints on the non-combustible material must be sealed using the manufacture’s recommended method. The area between the insert and the recess must be ventilated according to the specification/dimension diagrams on page 31. - Page 14 RECESSING ThE INSERT Recess example Note! Note! The dimensions are the minimum The dimensions are the minimum dimensions, unless otherwise stated. dimensions, unless otherwise stated. Wall of combustible material Wall of non-combustible material, made of 100 mm aerated concrete in the recess example.
- Page 15 RECESSING ThE INSERT Avtätning Heat Shield Area min. 600cm Area min. 600cm Area ut min. 600 cm Area ut min. 600 cm Area in min. 600 cm Area min. 600cm Area in min. 600 cm Area min. 600cm Area min. 600cm Area ut min.
- Page 16 NIBE AB · Box 134 · SE-285 23 Markaryd · Sweden www.contura.eu Contura reserves the right to change colours, materials, dimensions and models at any time without special notice. 811052 IAV SE-EX Ci10/Ci20-6 Your dealer can give you the most up to date information.