Using With An Analog Video Unit And Your Computer - Signal Convert Function (Dcr-Pc9E Only) - Sony DCR-PC6E Service Manual

Dubbing only desired scenes
– Digital program editing
Operation 1: Making the
Programme
(1) Insert the tape for playback into your
camcorder, and insert a tape for recording
into the VCR.
(2) Press FN to display PAGE1.
(3) Select VIDEO EDIT in in the menu
settings (p. 134).
Then press EXEC.
(4) Search for the beginning of the first scene you
want to insert using the video control buttons
on the LCD screen, then pause playback. You
can fine-adjust one frame at a time.
(5) Press MARK IN on the screen.
The IN point of the first programme is set,
and the top part of the programme mark
changes to light blue.
(6) Search for the end of the first scene you want
to insert using the video control buttons on
the LCD screen, then pause playback.
(7) Press MARK OUT on the screen.
The OUT point of the first programme is set,
then the bottom part of the programme mark
changes to light blue.
(8) Repeat steps 4 to 7.
When one programme is set, the programme
mark changes to light blue.
You can set 20 programmes in maximum.
3
5~8
V I DEO ED I T 0:08:55:06
MARK START UNDO ERASE
OUT ALL
TOTAL 0:00:00:00
SCENE 0
110
Dubbing only desired scenes
– Digital program editing
Operation 2: Performing a
Digital program editing
(Dubbing a tape)
Make sure your camcorder and the VCR are
connected, and that the VCR is set to recording
pause. When you use an i.LINK cable (DV
connecting cable) the following procedure is not
necessary.
When you use a digital video camera recorder,
set its power switch to VCR/VTR.
(1) Select VIDEO EDIT in in the menu
settings. Then press START.
(2) Press EXEC.
Search for the beginning of the first
programme, then start dubbing.
The "SEARCH" indicator appears during
search, and the "EDITING" indicator appears
during edit on the LCD screen.
The programme mark changes to light blue
after the dubbing is complete.
When the dubbing ends, your camcorder and
the VCR automatically stop.
To stop dubbing during editing
Press CANCEL.
To finish the Digital program editing
function
Your camcorder stops when the dubbing is
complete. Then the display returns to VIDEO
EDIT in the menu settings.
Press END to end the video edit function.
You cannot record on the VCR when:
– The tape has run out.
– The write-protect tab on the cassette is set to
lock.
– The IR SETUP code is not correct. (When IR is
selected.)
– The button to cancel recording pause is not
correct. (When IR is selected.)
– The programme to operate the Digital program
editing has not been made.
– i.LINK is selected but an i.LINK cable (DV
connecting cable) is not connected.
– The power of the connected VCR is not turned
on.
112
1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
EXIT
OTHERS V I DEO ED I T 0:32:30:14
DATA CODE
BEEP MARK START UNDO ERASE
COMMANDER I N ALL
D I SPLAY READY
V I DEO ED I T
ED I T SET
TOTAL 0:00:00:00
SCENE 0
END
EXEC RET.
V I DEO ED I T 0:09:07:06 V I DEO ED I T 0:10:01:23
MARK START UNDO ERASE MARK START UNDO ERASE
I N ALL I N ALL
TOTAL 0:00:13:00 TOTAL 0:00:47:12
SCENE 1 SCENE 3
END END END
2
(1)
(2)
Dubbing only desired scenes
– Digital program editing
Erasing the programme you have set
Erase OUT mark first, and then IN mark of the
last programme.
(1) Press UNDO. The last programme mark
flashes on the LCD screen.
(2) Press EXEC. The setting is cancelled.
To cancel erasing
Press CANCEL in step 2.
Erasing all programmes
(1) Select VIDEO EDIT in
in the menu
settings.
(2) Press ERASE ALL. All the programme marks
flash on the LCD screen.
(3) Press EXEC. The settings are cancelled.
To cancel erasing all programmes
Press CANCEL in step 3.
To finish making programmes
Press END.
The programme is stored in memory until the
tape is ejected.
Note
You cannot operate recording during the Digital
program editing.
On a blank portion of the tape
You cannot set IN or OUT.
If there is a blank portion between the IN
point and the OUT point on the tape
The time code may not be displayed correctly.
Using with an analog video
unit and your computer
– Signal convert function
– DCR-PC9E only
You can capture images and sound from an
analog video unit connected to your computer
which has the i.LINK jack (DV jack) to your
camcorder.
Before operation
Set DISPLAY to LCD in the menu settings. (The
default setting is LCD.)
(1) Set the POWER switch to VCR.
(2) Press FN to display PAGE1.
(3) Press MENU, then set A/V t DV OUT to
ON in in the menu settings (p. 134).
(4) Start playback on the analog video unit.
(5) Start capturing procedures on your computer.
The operation procedures depend on your
computer and the software which you use.
For details on how to capture images, refer to
the instruction manual of computer and the
software.
OUT
S VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
: Signal flow/
1-26
(1)
(2)
(1)
(2)
(3)
(1)
(2)
(3)
t
(4)
(5)
A/V
i. LINK
DV
(optional)/
111
113