Table of Contents
Advertisement
DAY/NIGHT SERvICE CHANGEOvER
To change from DAY to NIGHT service, press the
with the
service button. How changeover takes place will depend
on the type of installation.
Case : System with a single switchboard station
The switchboard station passes to night service mode and calls made
from the main entrance panels are sent directly to the apartment
stations.
The switchboard station intercepts calls from apartment stations if they
belong to the zone assigned to it.
Case 2: System with several switchboard stations in parallel
Where there are two or more switchboard stations operating in parallel
(i.e., when the same zone is assigned to all switchboard stations), the
switchboard station passes to night service mode and calls made from
the main entrance panels are:
• Intercepted by the other switchboard stations operating in day
service mode if they belong to the zone assigned to them.
• Sent directly to the apartment stations if the latter do not belong to
the zone assigned to the other switchboard stations operating in day
mode, or if all switchboard stations are in night mode.
The switchboard station intercepts calls from apartment stations if they
belong to its assigned zone.
Case 3: Multiple switchboard stations with specific zone
assignments
Where there are two or more switchboard stations with specific zone
assignments (i.e., where each switchboard station is assigned to a
different zone), the switchboard attendant can:
• Pass to night service mode without transferring management of
his zone to another switchboard station. In this case, calls made
from the main entrance panels are intercepted by other switchboard
stations operating in day service mode if they belong to the zone
assigned to them, or are sent directly to the apartment stations if the
latter do not belong to the zone assigned to the other switchboard
stations operating in day mode, or if all switchboard stations are
in night mode. Calls originating from apartment stations are not
put through, or are intercepted by the other switchboard stations
responsible for the zone involved.
• Pass to night service mode and transfer management of his zone
to another switchboard station in the system. In this case, the latter
switchboard station will be responsible for its own zone and for the
transferred zone, both as regards calls made from main entrance
panels and as regards calls originating from apartment stations. LED
on the receiving switchboard station will go on to indicate that
zones belonging to other switchboard stations are being handled
(see below).
Example: System with three switchboard stations identified by codes
1, 2, and 3. If the attendant of switchboard station 1 wishes to pass
to night service mode and thus presses
station will display the following message:
DiVERT TO S.BOARD:
----
If the attendant does not wish to transfer the zones assigned to his
station, he presses the call button
passes to night service mode.
If the attendant wishes to transfer his zones to another switchboard
station, he presses key
6
−−−− sec.5a
GUARD DOOR SWITCHBOARD STATION Ref. 038/40
OPERATING INSTRUCTIONS
key together
SHIFT
-
, the switchboard
SHIFT
and the switchboard station
as many times as needed to select the
desired switchboard station. For instance, if key
the display will show:
DiVERT TO S.BOARD:
0003
If the attendant then presses the call button
station will pass to night service mode and its assigned zones will be
transferred to switchboard station 3. In this case, switchboard station 1
will not intercept calls originating from apartment stations.
NIGHT/DAY SERvICE CHANGEOvER
To change from NIGHT to DAY service, press the
with the
service button on the switchboard station. The switchboard
station will immediately resume control of its assigned zones. Thus, if
the switchboard attendant transferred his zones to another switchboard
station upon passing to night service mode, the transfer will end at this
time.
vIEWING ZONE ASSIGNMENTS
As described above, each switchboard station is assigned a zone
consisting of two ranges of apartment station codes. The switchboard
station can intercept calls made from main entrance panels and
directed to apartment stations whose codes are included in one of
these two ranges. Likewise, it can intercept calls originating from
apartment stations whose codes are included in one of the two
ranges.
To view the zone assigned to a switchboard station, press key
under normal operating conditions.
Example:
0002-9999 J000-JJJJ
0003
This means that the switchboard station identified by code 0003 is
responsible for the user codes between 2 and 9999 and between J000
and JJJJ.
In systems with several switchboard stations that do not operate in
parallel, if a switchboard station transfers its zones to another upon
passing to night service mode, LED
go on. To view the zones received by this station and the codes
for the switchboard stations which transferred them, press key
several times in succession. For example, if the switchboard station
identified by code 0003 receives the zone consisting of codes A000-
AJJJ + C000-D000 from switchboard station 0001, pressing key
switchboard 0003 twice will cause the display to show:
A000-AJJJ C000-D000
0003
This information will be displayed for a maximum of 10 seconds.
is pressed twice,
, the switchboard
key together
SHIFT
on the receiving station will
on
DIGIVOICE - Technical Manual
Hide quick links:
Advertisement
Table of Contents
