Operation - urmet domus 1138/18 Manual

STEP 7 - CALLING MODE
Enter 3 to select 'UNRESTRICTED' calling mode, 2 to select
'PROGRAMMED' calling mode, or 1 to disable the doorphone from
making outgoing calls. After the 7th programming step is completed,
the configuration cycle comes to an end.
Note: if 2 is selected in this step, it is not necessary to carry out the
extended programming sequence to assign codes to each
key.
EXTENDED PROGRAMMING
This programming sequence must be performed when the doorphone
has been configured for 'PROGRAMMED' calling mode, and makes it
possible to associate each of the 20 keys (1 through 0, A through J)
with a different function. This function may be a call, a special service
code, or a main entrance panel self-activation code.
To activate the extended configuration cycle, hold down the SHIFT
key (5) and press key (6) several times in succession until LED (11)
begins to flash red and green. This operation will take effect ONLY
if the doorphone has already been configured for 'PROGRAMMED'
calling mode.
At this point, functions can be assigned to keys. First press the key to
be programmed (0 through 9 or A through J). LED (11) will flash more
quickly. Then program the function to be associated with the pressed
key. LED (11) will flash slowly. Repeat the procedure for all keys to
be programmed and then exit from programming with the same key
sequence used to activate the cycle.
Function programming
Any of the following functions can be associated with a doorphone
key:
1) Call to another user
2) Special service code
3) Main entrance panel self-activation.
To program a call to another user, press the key to be programmed,
enter the user code (this code must not begin with 0), and confirm by
pressing the call button (4).
To program a special service code, press the key to be programmed,
enter the special service code (beginning with 0), and confirm by
pressing the call button (4).
To program main entrance panel self-activation, press the key to be
programmed, enter the main entrance panel code (this code must not
begin with 0), and confirm by pressing key (13).
Note: to annul the function programmed for a key, simply program
it for a function that has no effect on the system (e.g., special
code 0JJJ).
DEFAULT PROGRAMMING
When it leaves the factory, the special doorphone is configured as
follows:
• Riser cable:
• Code:
• Engaged time:
• Ring duration:
• Lines:
• RCH:
• Calling mode:
DIGIVOICE - Technical Manual
SPECIAL DOORPHONE Ref. 38/8

OPERATION

01
1000
20 s
3 s
1
0
UNRESTRICTED
• 20 pre-programmed functions:
OPERATION
RECEIvING CALLS FROM ENTRANCE PANELS OR
GUARD DOOR SWITCHBOARD STATION
When the call is received, the doorphone will ring with the distinctive
tone used to identify the calling device. Picking up the handset will
establish communication with the caller. As the call will be cut off
immediately when the handset is hung up, the door lock release key
must be actuated BEFORE hanging up if it is necessary to open the
door.
RECEIvING AND STORING CALLS FROM OTHER
APARTMENT STATIONS
The special doorphone can receive calls from other apartment stations
in the system and store unanswered calls in memory. This function
can be disabled by pressing the SHIFT and Door Lock Release keys
(5) -(15). If the function is disabled, LED (12) will flash once every 2
seconds, and incoming calls will be ignored but stored in memory. To
enable the doorphone to receive calls again, simply press SHIFT and
the Door Lock Release key again.
When the special doorphone receives a call from another apartment
station, it rings with the distinctive tone used to identify these stations
and LED (12) will go on for a maximum of 10 seconds. If the handset
is picked up within 10 seconds, communication is established with the
caller and the LED goes off. If the call is not answered, it will be stored
in memory, and LED (12) will flash.
To return a call that has been stored in memory, simply pick up
the handset and press the CALL button (4). If the other apartment
station does not answer, the call is not deleted from memory, and any
other calls queued in the memory can be returned by hanging up the
handset and then repeating the procedure. The doorphone will emit a
warning tone when the handset is hung up if the memory still contains
calls that have not been reviewed. All calls in the memory can be
erased by pressing SHIFT-X (5)-(3).
Note: a maximum of ten calls can be stored in memory.
CALLING OTHER DOORPHONES
Depending on how it was configured, the special doorphone can
make calls to other apartment stations by dialing the associated code
('unrestricted' calling mode) or to a maximum of 20 preprogrammed
apartment stations ('programmed' calling mode). The special doorphone
can also be configured so that it can only return calls stored in its
memory.
Regardless of whether the doorphone has been configured for
'unrestricted' calling mode or for 'programmed calling mode, the
following points must be borne in mind:
1) Calls can only be made with the handset off-hook.
2) Calls to other apartment stations can only be made if the doorphone
is not already engaged in a voice communication. If it is, it will be
necessary to hang up the handset and then pick it up again.
3) The doorphone will emit 3 single-tone beeps when a call is made.
If it does not, the code you are attempting to call does not exist.
4) If a call cannot be made because the line is engaged, the
doorphone will emit a series of beeps similar to a normal telephone
busy signal: hang up and try again later.
5) Calls to another apartment station can last no longer than 10
minutes. They will be cut off automatically at the end of this timeout
period, or if other calls are made on the system.
'UNRESTRICTED' calling mode
To call another apartment station, dial its code (which must not begin
with '0' and may consist of a maximum of 4 characters) using the
keypad (2) and press the call button (4). Letter codes can be dialed by
using the SHIFT key (5) in the same way as on a computer keyboard:
to dial the letter 'B', for example, hold down the SHIFT key and press
'2').
Call code 1000.
2
sec.5a −−−−