Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech IDK-121R-42XGA1
Summary of Contents for Advantech IDK-121R-42XGA1
- Page 1 User Manual IDK-121R-42XGA1 TFT-LCD 12” XGA (LED Backlight)
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
- Page 4 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
-
Page 5: Table Of Contents
Contents Chapter Overview..........1 General Description .................. 2 Display Characteristics................2 Mechanical Specification................2 Mechanical Dimension ................3 1.4.1 Frontview ..................3 1.4.2 Rearview ..................4 Absolute Maximum Ratings ..............5 1.5.1 Absolute Ratings of the TFT LCD Module ........5 1.5.2 Absolute Environment Ratings............ - Page 6 Chapter Touch Controller ....... 25 Touch Controller Characteristics............. 26 6.1.1 Specifications................26 6.1.2 Environmental Features.............. 26 Pin Assignment and Description ............. 27 6.2.1 Photo ..................27 6.2.2 Combo Interface Connector, JP1, Pins and Signal Descriptions 27 6.2.3 Connectors and Pin Definitions ..........27 6.2.4 USB, Serial connector, and Signal Descriptions......
-
Page 7: Chapter 1 Overview
Chapter Overview... -
Page 8: General Description
General Description IDK-121R-42XGA1 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver circuit, backlight system and 5-wire resistive touch. The screen format is intended to support the XGA (1024(H) x 768(V)) screen and 16.2M/ 262k colors (RGB). -
Page 9: Mechanical Dimension
Mechanical Dimension 1.4.1 Frontview IDK-121R User Manual... -
Page 10: Rearview
1.4.2 Rearview IDK-121R User Manual... -
Page 11: Absolute Maximum Ratings
Absolute Maximum Ratings 1.5.1 Absolute Ratings of the TFT LCD Module Value Item Symbol Unit Min. Max. Logic/LCD Drive Voltage -0.3 +3.6 [Volt] 1.5.2 Absolute Environment Ratings Value Item Symbol Unit Min. Max. Operating Temperature °C Operation Humidity [%RH] Storage Temperature °C Storage Humidity [%RH]... - Page 12 IDK-121R User Manual...
-
Page 13: Chapter 2 Electrical Characteristics
Chapter Electrical Characteristics... -
Page 14: Tft Lcd Module
TFT LCD Module 2.1.1 Power specification Value Parameter Symbol Unit Remark Min. Typ. Max. Logic/LCD Input Volt- [Volt] LCD Input Current [mA] VDD=3.3V at 60 HZ, all Black Pattern LCD Power 1.95 2.34 [Watt] VDD=3.3V at 60 HZ, all Black Pattern LCD Inrush Current Note 1;... -
Page 15: Backlight Unit
Differential Input Low [mV] VICM=1.2V Threshold Input Differential Voltage VID [mV] Differential Input Com- VICM 1.15 1.45 VTH/VTL=100mV mon Mode Voltage Note LVDS Signal Waveform. Backlight Unit 2.2.1 Parameter guideline for LCD The following characteristics are measured under a stable conditions using an inverter at 25°C (Room Temperature): Value Parameter... - Page 16 LED Forward Current [mA] Ta = 25°C LED Forward Voltage (30.33) 36 [Volt] = 110mA, a = -30°C (27.81) 36 [Volt] = 110mA, a = 25°C (26.1) [Volt] = 110mA, a = 85°C LED Power Consump- (6.12) 7.92 [Watt] tion Operation Lifetime 50,000 - IF = 110mA, Ta = 25°C...
-
Page 17: Chapter 3 Signal Characteristics
Chapter Signal Characteristics... -
Page 18: Pixel Format Image
Pixel Format Image The following figure shows the relationship between the input signal and the LCD pixel format. 3.1.1 Pin Description Table 3.1: Pin Description Pin No. Symbol Description Power supply,3.3V (typical) Power supply,3.3V (typical) Ground SEL68 6 / 8-bits LVDS data input selection [H: 8bits L/NC: 6bit] *Note 4 RIN0- LVDS differential signal channel 0 LVDS differential data input (R0, R1, R2, R3, R4, R5, G0) -
Page 19: The Input Data Format
Note 1 Input signals shall be in low status when VDD is off. Note 2 High stands for “3.3V”, Low stands for “0V”, NC stands for “No Connection”. Note 3 RSV stands for “Reserved”. Note 4 Input signals shall be in low status when VDD is off. Note 5 If in 6-bit mode, please keep pin 17 &... -
Page 20: Tft-Lcd Interface Timing
+GREEN5(G5) Green Data 5(MSB) Green-pixel Data +GREEN4(G4) Green Data 4 Each green pixel’s brightness data consists of +GREEN3(G3) Green Data 3 these 6 bits pixel data. +GREEN2(G2) Green Data 2 +GREEN1(G1) Green Data 1 +GREEN0(G0) Green Data 0(LSB) Green-pixel Data +BLUE5(B5) Blue Data 5(MSB) Blue-pixel Data... -
Page 21: Input Timing Diagram
3.3.2 Input Timing Diagram Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power ON/OFF Sequence Timing Parameter Value Unit... - Page 22 [ms] [ms] 1000 [ms] The above on/off sequence should be applied to avoid abnormal functions in the dis- play. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. IDK-1112R User Manual...
-
Page 23: Chapter 4 Connector & Pin Assignment
Chapter Connector & Pin Assignment... -
Page 24: Tft-Lcd Signal (Cn1): Lcd Connector
The physical interface is described as below for the connector on module. These connectors are capable of accommodating the following signals. TFT-LCD Signal (CN1): LCD Connector Table 4.1: Connector Connector Name / Description Signal Connector Manufacturer STM or compatible Connector Model Number MSB240420-E or compatible Adapable Plug P240420 or compatible... - Page 25 Mating Model Number(CN3) 3808K-F03N-02R or compatible Pin No. Symbol Description Color Pin1 LED anode Pin2 LED cathode White Pin3 LED cathode Black IDK-1112R User Manual...
- Page 26 IDK-1112R User Manual...
-
Page 27: Chapter 5 Touch Screen
Chapter Touch Screen... -
Page 28: Touch Characteristics
Touch Characteristics This touch panel is a resistance type used with flat LCD type displays. Once touched by stylus or finger, it sends coordinate points to PC from the voltage changes at the contact point. Optical Characteristics Item Specification Remarks 80% ... -
Page 29: General Specification
General Specification Item Specification Frame size 261.80 0.30 X 199.80 0.30 mm View Area 249.80 0.20 X 188.50 0.20 mm Active Area 246.80 0.20 X 185.50 0.20 mm Total Thickness 2.20 0.20 mm ... - Page 30 IDK-1112R User Manual...
-
Page 31: Touch Controller
Chapter Touch Controller... -
Page 32: Touch Controller Characteristics
Mtouch/Chenmtech Co., Ltd MTC7000C touch control board meets latest Restriction of Hazardous Substances (ROHS) directive. This touch panel controller provides excellent performance of your analog resistive touch panels for 4/5 wire models. The touch panel driver emulates mouse left and right button functions and supports the following. -
Page 33: Pin Assignment And Description
Pin Assignment and Description 6.2.1 Photo JP1 Connector (USB&RS-232 Combo Interface) JP2 Connector (5-wire Touch screen interface) 6.2.2 Combo Interface Connector, JP1, Pins Signal Descriptions The combo interface connector, USB and RS-232, is a box 2.0mm 10-pins 90 degree, Male type with lock connector, intended to be used with single wired pins in 5+5 pins header. -
Page 34: Touch Screen Connector, Jp2, Pins And Signal Descriptions
Pin diagram for USB and serial connector, J1/J6, as viewed from connector mating surface. 6.2.5 Touch Screen Connector, JP2, Pins and Signal Descriptions Touch screen connector, J2(J4 for MTC7000C), is a dual row by five-position header with 0.025-inch square pins spaced on 0.100 centers. 5W sensor must be connected to the upper row of the connector. -
Page 35: Appendix A Optical Characteristics
Appendix Optical Characteristics... -
Page 36: Optical Characteristics
Optical Characteristics The optical characteristics are measured under stable conditions at 25°C (Room Temperature): Item Conditions Min. Typ. Max. Unit Note White IF= 80mA/1 LED [cd/m2] Note 1 Luminance Line (center point) Uniformity 5 Points Note 2, Contrast Ratio Note 4 Response Time Rising [msec]... - Page 37 Note2 Definition of 5 points position (Display active area: 246mm (H) x 184.5mm(V)) Note3 The luminance uniformity of 5 points is defined by dividing the minimum luminance values by the maximum test point luminance. Note4 Definition of contrast ratio (CR): Note5 Definition of response time: The output signals of photo detector are measured when the input signals...
- Page 38 IDK-1112R User Manual...
-
Page 39: Appendix B Handling Precautions
Appendix Handling Precautions... -
Page 40: Handling Precautions
Handling Precautions The optical characteristics are measured under stable conditions at 25°C (Room Temperature) Since front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input con- nector. - Page 41 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2015...