No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 Years) Advantech warrants the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation.
General Description The Advantech IDK-1110WP series comes with a 10.1″ industrial-grade LCD display with projected capacitive touch. The series is also available with flexible options for LCD screens with enhancements such as an anti-reflective surface treatment and optical bonding solution. The IDK-1110WP series has low power consumption, typi- cally running at 6.18 W.
Note (1): Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2): Specified values are for LED (Refer to 2.1.2 for further information). IDK-1110WP-50XGB2 User Manual...
“H” Level Voltage for LVDS “L” Level -100 Receiver Threshold Terminating Resistor Note (1): The module should be always be operated within the above ranges. Note (2): Measurement Conditions: The rise time of Vcc is 470 s. IDK-1110WP-50XGB2 User Manual...
Active Area Active Area Note (4): The power consumption is specified for the pattern with the maximum current. Note (5): VID waveform condition. Vcc Power Dip Condition Dip condition: 4.0V ≤ Vcc ≤ 4.5V, Td ≤ 20ms IDK-1110WP-50XGB2 User Manual...
Level Dimming Control (E_PWM) PWM Low Level 0.15 Level PWN Noise Range VNoise PWM Control Frequency (2), Suggestion @ 190Hz ≤f <1kHz PWM Dimming Control Duty Ratio (2), @ 1kHz ≤f ≤ 20kHz LED Lifetime 50,000 - IDK-1110WP-50XGB2 User Manual...
NC → 6-bit Input Mode. High → 8-bit Input Mode No connection, this pin should be open No connection, this pin should be open LED_VCC Converter input voltage 12V LED_VCC Converter input voltage 12V LED_VCC Converter input voltage 12V IDK-1110WP-50XGB2 User Manual...
Page 17
Note (4): Interface optional pin has an internal scheme as in the following diagram; the user should keep the interface voltage level requirement, including the panelboard loading as shown below. Note (5): Pin1 location is Power Supply 5V to comply with mechanical characteristics. IDK-1110WP-50XGB2 User Manual...
Note (1): Because this module is operated in DE-only mode, Hsync and Vsync input signals should be set to low logic level or ground. Otherwise, this module will operate abnormally. Note (2): The Tv (Tvd+Tvb) must be an integer; otherwise, the module will operate abnormally. Input Signal Timing Diagram IDK-1110WP-50XGB2 User Manual...
Page 21
Note (a): The input clock cycle-to-cycle jitter is defined in the below figures. T = I T1 – Note (b): Input Clock to data skew is defined as in the below figures. Note (c): The SSCG (spread spectrum clock generator) is defined as in the below fig- ure. IDK-1110WP-50XGB2 User Manual...
(4) T4 should be measured after the module has been fully discharged between power off and on periods. (5) The interface signal should not be kept at high impedance when the power is on. IDK-1110WP-50XGB2 User Manual...
The following figures show the image seen from the front. The arrow indicates the direction of scan. PCBA on the bottom side PCBA on the bottom side Fig. 1: Normal scan (pin 28, UD/LR = Low or NC) Fig. 2: Reverse scan (pin 28, UD/LR = High) IDK-1110WP-50XGB2 User Manual...
COF (Chip on FPC tail) FPC Tail Bending Radius R2.5 mm Peeling upward 90deg with 500gw without impact to electric Holding Force for Tail performance. Connector Pins & Pitch 5 pins, pitch is 1.25 mm Top Surface Finish Type Clear IDK-1110WP-50XGB2 User Manual...
Touch Controller Advantech’s IDK-1110WP series projective capacitive touchscreen adopts a COF (Chip on FPC) design, so an extra touch control board is not required. This communi- cates with a PC system directly through USB connectors. The superior design is sen- sitive, accurate, and user friendly.
Page 28
1258WOR0-05K). The pins are numbered as shown in the table below. Table 3.4: USB Interface Connector and Pin Assignment Pin No. Symbol Remarks Ground Pull low voltage to disable the touch function. Releas- ing this pin will re-enable the touch function. IDK-1110WP-50XGB2 User Manual...
90°(θ) horizontal left and right, and 90°(ɸ) verti- cal high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated to its center to develop the desired mea- surement viewing angle. IDK-1110WP-50XGB2 User Manual...
Page 31
The LCD module should be stabilized at a given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting the backlight for 20 minutes in a sta- ble, windless, and dark room. IDK-1110WP-50XGB2 User Manual...
Page 32
“Full Black” to “Full White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response time is an interval between 10% and 90% of amplitudes. Please refer to the figure below. Optical Optical White White Black Black White White response response IDK-1110WP-50XGB2 User Manual...
Display quality may be reduced if the ambient temperature is lower than 10ºC. For example, the response time may become slow, and the starting voltage of the lamp will be higher than at room temperature. IDK-1110WP-50XGB2 User Manual...
In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. After the module’s end of life, there will be nothing harmful if operated and stored normally. IDK-1110WP-50XGB2 User Manual...
Need help?
Do you have a question about the IDK-1110WP-50XGB2 and is the answer not in the manual?
Questions and answers