Hard Disk Drives - Asus Motherboard NCLV-D2 Series Product Manual

3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA

hard disk drives.

If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 set LSI Logic Embedded SATA RAID in the Intel
Southbridge chip.
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S
the BIOS to [Yes]. See section "4.3.4 IDE Configuration" for details.
NCLV-D2/SATA SATA connectors
NCLV-DS2 SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
•
•
•
2 - 2 8 2 - 2 8
2 - 2 8 2 - 2 8 2 - 2 8
You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0 or RAID 1) is available only if you are
using Windows ® 2000/XP.
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1 set.
When using the connectors in Standard IDE
(boot) hard disk drive to the SATA1 connector. Refer to the table on the
next page for recommended SATA hard disk drive connections.
S t a n d a r d I D E mode by default. In S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E
C o n f i g u r e S C o n f i g u r e S C o n f i g u r e S- - - - - A T A C o n f i g u r e S A T A A T A A T A a s R A I D A T A
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
® 2000 Service Pack 4 or the Windows
Standard IDE Standard IDE mode, connect the primary Standard IDE
Standard IDE
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
® 6300ESB
a s R A I D item in a s R A I D a s R A I D a s R A I D
® XP