Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Dog trace d-control 600
Summary of Contents for Dog trace d-control 600
- Page 1 d–control 600,1000,1600 Electronic training collar User guide...
- Page 2 IČO: 64793826 declares under own responsibility that the product: Electronic training collar Dogtrace d-control 600, 1000 and 1600 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC from 9. 3. 1999 meets requirements of General Licence of The Czech Telecommunication Office according to general licence no.
-
Page 3: Important Notice
Hereby, VNT electronics s.r.o. , declares that this d-control 600, 1000, 1600 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Thank you for purchasing the product Dogtrace d-control 600, 1000 or 1600 from VNT electronics s.r.o., Czech Republic. -
Page 4: Ecma
ECMA NT electronics s.r.o., professional producer of the dog training equipment, which is manufactured and sold under the brand name Dogtrace, is a proud and active member of the Electronic Collar Manufacturers Association. ECMA was founded in Brussels in 2004 as a result of increasing awareness from different manufacturers concerning the necessity of regulating their industry. -
Page 5: Table Of Contents
Contents Important notice ..............3 ECMA . -
Page 6: Introduction
Features of d-control 600, 1000 and 1600 The electronic training collars d-control 600, 1000 and 1600 feature with audible beeb tone, electronic stimulation impuls and booster function. Booster function allows you to select any intensity of stimulation impulse (00-30), but normally higher than selection of the standard stimulation impulse. -
Page 7: Package Contents
Package contents transmitter with belt clip reciver (with the strap)* 2 pairs of contact points (12 mm and 17 mm)* 1 lithium battery CR2 3V* 2 alkaline batteries AA 1,5 V * test discharge lamp* ... -
Page 8: Product Description
Product description TRANSMITTER RECEIVER WITH THE STRAP LCD PANEL TRANSMITTER − 1 - LCD panel, 2 - button for booster, 3 - button for stimulation impulse, 4 - button for audbile beep tone, 5 - button for power ON/OFF, 6 - buttons for stimulation level selection, 7 - buttons for dog selection 1 or 2 RECEIVER WITH THE STRAP −... -
Page 9: Transmitter Preparation
Transmitter preparation Battery insertion and replacement 1. Screw out screw from the battery cover using a cross-head screwdriver and carefully remove the lid. 2. Insert two alkaline AA batteries into the battery compartment with a correct polarity (according to the polarity indicated with the “+” symbol in the battery compartment). Wrong polarity may damage the unit. -
Page 10: Receiver Preparation
Receiver preparation Battery insertion and replacement 1. Screw out 4 screws from the battery cover using a cross-head screwdriver and remove the lid. 2. Insert the lithium CR2 3V battery into the battery compartment with a correct polarity (according to the polarity indicated with the “+” symbol in the battery compartment – see the Fig.). - Page 11 Switching the receiver ON / OFF To turn the receiver ON / OFF ( or for programming the transmitter with the receiver) is used a magnetic switch, marked with the red target on the receiver. The receiver is activated when the magnet in bottom of the transmitter, is enclosed to the red target on the receiver. Switching ON Move the red target of the receiver towards the bottom of the transmitter for 1 second (see the Fig.).
-
Page 12: Programming (Pairing) Of The Transmitter And The Receiver
(this can be followed when you use d-control 600, 1000 or 1600 with a new purchased receiver or when you purchased d-control 602, 1002 or 1602). - Page 13 Reprogramming of your receiver The receiver can be programmed repeatedly without restraint using the same transmitter or another (see the section Programming (pairing) of the transmitter and the receiver). TIP: It is possible to program an unlimited number of receivers to a one transmitter. Example: Button is paired with 3 receivers, they can be programmed one by one or we can set all 3 in pairing regime and then press button for audible beep tone.
-
Page 14: The Basics Of A Training Collar Usage
trim the hair in the area of the contact points or to switch to the longer contact points to ensure a consistent contact. WARNING: If the collar is too loose, the receiver is likely to move and the repeating friction can irritate the skin of your dog. Furthermore, in this case is not ensured a reliable contact of contact points with the skin and a proper function of the training collar. - Page 15 but do not use it so that your pet does not discover the connection with its attachment and effects. Affirmative and efficient training requires some time: don‘t hurry! Select a well-known environment your dog is used to. Choose the right moment to press the button; exactly at the moment when your dog ...
- Page 16 be set by guess. Start from the lowest level. When your dog doesn't react to the low level stimulation, gradually set the level higher, and carry on until you see slight reaction. Stimulation impulse should never create fear or pain. The choice of momentary (nick) or continuous stimulation impulse Stimulation impulse features functions A and B, which are switched by repetitive press of button...
-
Page 17: External Remote Control - One Touch
Booster button setting: Press continuously button for the choice of the dog 1 or 2 (button for receiver 1 or for receiver 2 according to required pairing), until you see on LCD symbol 1/2 flashing. With the buttons choose requiered intensity of the stimulation impulse on the booster button. -
Page 18: For The Best Results
For the best results The training collar d-control 600, 1000 and 1600 can be used up to 600, 1000, 1600 m working range. The maximum range depends on many factors - weather, terrain, vegetation and so on. To ensure maximum working range of the device: Do not cover the transmitter antenna. -
Page 19: Troubleshooting
Thicker fur dog – it is necessary to tighten the collar so that the permanent contact with the dog‘s skin is ensured. If the fur is too thick, it is recommended to cut the hair or choose a longer type of contact points. Battery properties change –... -
Page 20: Maintenance
touch with the screw and tighten them (see picture). Turn ON the transmitter and the receiver. Select stimulation function button. The test discharge lamp will increase a light intensity when increasing stimulation level. Note: When is the level set to 00 there is no stimulation. -
Page 21: Technical Specifications
Technical specifications TRANSMITTER Range........600, 1000, 1600 m ... -
Page 22: Warranty Terms And Conditions
Warranty terms and conditions VNT electronics s.r.o. provides a 2 year warranty on the Dogtrace products with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: batteries ... - Page 23 4. The claimant is obliged to prove the defect and to enable the manufacturer to check the legitimacy of the product faults and assess the extent of the product faults. Otherwise is loosing the right arising from the manufacturer’s responsibility for product defect. 5.
-
Page 24: Certificate Of Warranty
Manufacturer: VNT electronics s.r.o. Smetanovo náměstí 104 570 01 Litomyšl Czech Republic Phone: +420 733 121 890 www.dogtrace.com Version 2016-5-20 / EN Duplication of this manual without the exclusive consent of VNT electronics s.r.o. is prohibited.