MUTOH VJ-2638 Installation Manual page 8

VJ-2638/1638/1638W Installation Manual
• Insert the cleaning cartridge all the way to
the end of the ink cartridge slot.
No1 Name No1
1 Cleaning cartridge 2 Ink cartridge slots
• If the head height is set to High, "Change
Head Gap Low" is displayed on Operation
panel. Set the head height to Low.
Operation manual "4.2.5.3 When
setting the head height to Low"
• When all cleaning cartridges are installed,
"Busy-Washing" is displayed on the operation
panel, and the printer starts charging the
cleaning fluid.
• When the cleaning fluid has been charged,
"Remove Cartridges" is displayed on the
operation panel.
51 Remove all the cleaning cartridges.
No1 Name
1 Cleaning cartridge
• "Busy-Washing" is displayed on the operation
pan el and the printer starts head cleaning.
• When head cleaning is complete, "Wash retry?
No" is displayed on the operation panel.
61 Press the [Enter] key on the operation
panel.
• "Insert InkCartridges" is displayed on the
operation panel.
VJ1638xE-I-03
71 Install Ink cartridges (K, C, M, Y: 2 each) in
Ink cartridge slots (K, C, M, Y: 2 each) on the
back of the printer.
• Shake Ink cartridge two to three times gently
before inserting it into Ink cartridge slot.
• Slots for ink cartridges are specified depending
on colors of the ink cartridges. Match the ink
color label with the ink color before inserting Ink
cartridge.
Name
• Keep the arrow of Ink cartridge facing up and
insert it into the printer.
No1 Name
1 Ink cartridge
2 Arrow
• Insert the ink cartridge all the way to the end
of the ink cartridge slot.
No1 Name
1 Ink cartridge
2 Ink cartridge slot K1
3 Ink cartridge slot K2
4 Ink cartridge slot C1
5 Ink cartridge slot C2
• When all the ink cartridges are installed, "Ink
Refill **%" is displayed on the operation panel
and ink replenishment starts.
• Initial filling takes time as follows.
• VJ-2638: about 20 minutes
• VJ-1638: about 17 minutes.
• Ink filling operation and pause operation are
repeated during the ink replenishment.
• W h e n " 1 0 0 % " i s d i s p l a y e d , t h e i n k
replenishment is complete.
• After the ink replenishment is complete,
"Media End" is displayed on the operation
panel.
・
●
No1 Name
3 Ink cartridge slot
4 Ink color label
●
No1 Name
6 Ink cartridge slot M1
91111
7 Ink cartridge slot M2
8 Ink cartridge slot Y1
9 Ink cartridge slot Y2
11
•
•
11
•
8
D o n o t p e r f o r m t h e f o l l o w i n g
operations during ink filling1 If filling
is interrupted,ink will be lost when
filling is resumed1
Do not turn OFF the power of the
•
printer1
Do not unplug the power cable of
•
the printer1
Do not open the front cover1
•
Do not open the maintenance cover1
•
Do not raise the media loading
•
lever1
If the printer performs the nozzle check
p r i nt i n g i m m e d i ate l y a f te r i n i t i a l i n k
replenishment is complete, the following
results may occur.
Printed lines become blurred.
•
The data is partially not printed.
•
In such cases, follow "6.2.3 Head
cleaning" and refill a small amount of
ink. Then, check the printing result.
If there is no improvement in the print result
even after refill a small amount of ink, leave
the printer unused for an hour or more. Then,
refill a small amount of ink again and check
the print result.
If there is still no improvement, contact
your local MUTOH dealer.
For VJ-1628W
Turn the printer ON.
The printer starts the initializing operation.
After the initial operation is compete,
"Start Ink Charge ? > E" is displayed on the
operation panel.
Press the [Enter] key on the operation
panel.
"Perform Washing? No" is displayed on the
operation panel.