MUTOH VJ-2638 Installation Manual page 10

VJ-2638/1638/1638W Installation Manual
● If the printer performs the nozzle check
p r i nt i n g i m m e d i ate l y a f te r i n i t i a l i n k
replenishment is complete, the following
results may occur.
Printed lines become blurred.
•
The data is partially not printed.
•
In such cases, follow "6.2.3 Head
cleaning" and refill a small amount of
ink. Then, check the printing result.
● If there is no improvement in the print result
even after refill a small amount of ink, leave
the printer unused for an hour or more. Then,
refill a small amount of ink again and check
the print result.
If there is still no improvement, contact
your local MUTOH dealer.
9.2 For 440ml Ink cartridges
(VJ-2638/1638)
● 440ml Ink cartridges are not compatible with
VJ-1638W.
11
Rotate Ink cartridge slots 90 degrees
upward.
No1 Name
1 Ink cartridge slots
11
Turn the printer ON.
• The printer starts the initializing operation.
• After the initial operation is complete, "Start
Ink Charge - > E" is displayed on the operation
panel.
21 Press the [Enter] key on the operation
panel.
• "Insert Cleaning cart." is displayed on the
operation panel.
VJ1638xE-I-03
41
Take out the cleaning cartridge(8pcs) from
the bag.
51
Set the cleaning cartridge to the ink
cartridge ink cartridge slot.
• Keep the arrow of Cleaning cartridge facing
up and insert it into the printer toward the
front side.
No1 Name No1
1 Cleaning cartridge 2 Arrow
• Insert the cleaning cartridge all the way to
the end of the ink cartridge slot.
No1 Name No1
1 Cleaning cartridge 2 Ink cartridge slots
• If the head height is set to High, "Change
Head Gap Low" is displayed on Operation
panel. (VJ-1638) Set the head height to Low.
Operation Manual"4.2.5 Head
Height Adjustment"
• When all cleaning cartridges are installed,
"Busy-Washing" is displayed on the operation
panel,and the printer starts charging the
cleaning fluid.
• When the cleaning fluid has been charged,
"Remove Cartridges" is displayed on the
operation panel.
61
Remove all the cleaning cartridges.
No1 Name
1 Cleaning cartridge
• "Busy-Washing" is displayed on the operation
panel and the printer starts head cleaning.
• When head cleaning is complete, "Wash retry?
No" is displayed on the operation panel.
10
71
Press the [Enter] key on the operation
panel.
• "Insert InkCartridges" is displayed on the
Name
operation panel.
81 Install Ink cartridges (K, C, M, Y: 2 each) in
Ink cartridge slots (K, C, M, Y: 2 each) on the
back of the printer.
• Shake Ink cartridge two to three times gently
before inserting it into Ink cartridge slot.
• S l o t s fo r i n k c a r t r i d g e s a re s p e c i f i e d
depending on colors of the ink cartridges.
Match the ink color label with the ink color
before inserting Ink cartridges.
• Keep the arrow of Ink cartridge facing up and
Name
insert it into the printer toward the front side.
No1 Name
1 Ink cartridge
2 Arrow
• Insert the ink cartridge all the way to the end
of the ink cartridge slot.
No1 Name
1 Ink cartridge
2 Ink cartridge slot K1
3 Ink cartridge slot K2
4 Ink cartridge slot C1
5 Ink cartridge slot C2
No1 Name
3 Ink cartridge slot
4 Ink color label
No1 Name
6 Ink cartridge slot M1
7 Ink cartridge slot M2
8 Ink cartridge slot Y1
9 Ink cartridge slot Y2